Bumper Mounts [Archive]

GVDrummer

04-02-2007, 16:34

It would depend on how you would mount your chassie and what material it would be made out of. You could screw them to it or go as simple as zip ties which are really light.

Al Skierkiewicz

04-02-2007, 17:07

The Tips and guidelines has some discussion on this subject. I saw all kinds of attachements last year but the ones that impressed me the most used a piece of aluminum angle drilled for mounting holes with bolts through the bottom of the chassis. The best one used eye bolts on the back of the bumpers which simply dropped over threaded rod on the chassis and attached with butterfly nuts. No tools needed and it only took a minute or so to remove for weigh in.

Kat Kononov

10-02-2008, 15:12

as simple as zip ties which are really light.

Are we allowed to use zip ties to mount the bumpers?

STANDARD BUMPERS must be
attached to the ROBOT with a bolt-and-
fastener system to form a
rigid, robust connection to the
ROBOT structure (i.e. not attached
with Velcro!).

Could someone please give some examples of "bolt-and-fastner" systems?

EricH

10-02-2008, 16:05

Are we allowed to use zip ties to mount the bumpers?

Could someone please give some examples of "bolt-and-fastner" systems?No. The GDC is very strict on the bumpers this year--it has to be something like a bolt-and-nut system.

TubaMorg

10-02-2008, 18:30

We use these with 1/4" 20 bolts. You just drill a 1/4" hole into your plywood and smack them in. Note that they need to go on the INSIDE of the bumper so that the bolt pulls them into the wood.

http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXK019

Sam N.

10-02-2008, 20:19

How do you mount your bumpers? 1351 is currently in discussion about the best (and strongest) way to attach them.

thanks,
Sam

I posted this a while ago and I've learned a lot since then. It is good to have your bumpers secured with big bolts but...

as long as the wooden backing of the bumper sits flush with your chassis, the bumper mounts only have to hold it in place. Any force imparted on the bumper should be translated to the chassis, not to the mount.

We use 1/4 inch aluminum angle. We may even downgrade that to save on weight.

Sam

Matt H.

10-02-2008, 20:26

Team 1726 has used either t-nuts (which can be hammered into a wooden board) or t-bolts to mount their bumpers. A quick McMaster search will show the various hardware. Considering the directions in which force will be applied to your bumpers you shouldn't need an incredibly tough mounting system as most of the force will be transmitted right on through as noted above.

You should be more worried if your bumpers are unsupported in the center as they may shatter.

M. Mellott

11-02-2008, 00:31

We used 1/4-20 carriage bolts hammered in the spec-size plywood through a 1/4" thru-hole. Typically, only 2 bolts per bumper are needed. The square shank under the head bites into the plywood and keeps the bolt from turning while being tightened. The bolts ran through holes drilled into the side frame members (1.5"x1.5" welded aluminum tubing frame) and fastened by wing nuts that are hand tightened (i.e. no tools).

The best one used eye bolts on the back of the bumpers which simply dropped over threaded rod on the chassis and attached with butterfly nuts. No tools needed and it only took a minute or so to remove for weigh in.

That is a very clever idea. Do you recall which team used that method?

We might look into using that ourselves--thank you!! :D

usbcd36

11-02-2008, 00:43

GaryVoshol

11-02-2008, 07:26

Last year, a member of another team told us that we shouldn't leave any mounting hardware on the bumpers apart from the bolts and/or nuts. I am beginning to doubt whether we would've failed inspection had we left our angles on the bumpers.

Is it legal to leave some light mounting hardware on the bumpers for inspection?

No. The only mounting hardware that is legal to be on the bumpers at inspection is the nut/bolt fastener as described in <R08>. Any other mounting hardware must be attached to the robot and be included in the robot size and weight restrictions.

[RMR662] Calle

13-02-2008, 20:57

Any other mounting hardware must be attached to the robot and be included in the robot size and weight restrictions.

Our team uses HDPE spacers to keep our bumpers offset the correct distance from our wheels. I understand these are most likely not legal bumper parts, and so will need to be included with the robot weight, but would it be acceptable to, after weighing in, reattach these spacers to the bumper, rather than the frame? For simplicity's sake, and just owing to the general design of our robot, this would be preferable.

EricH

13-02-2008, 21:08

Calle;698395']Our team uses HDPE spacers to keep our bumpers offset the correct distance from our wheels. I understand these are most likely not legal bumper parts, and so will need to be included with the robot weight, but would it be acceptable to, after weighing in, reattach these spacers to the bumper, rather than the frame? For simplicity's sake, and just owing to the general design of our robot, this would be preferable.That sounds like a good Q&A. Just remember that if you make finals, you'll have to take them off the bumpers again.

Al Skierkiewicz

14-02-2008, 07:24

Calle;698395']Our team uses HDPE spacers to keep our bumpers offset the correct distance from our wheels. I understand these are most likely not legal bumper parts, and so will need to be included with the robot weight, but would it be acceptable to, after weighing in, reattach these spacers to the bumper, rather than the frame? For simplicity's sake, and just owing to the general design of our robot, this would be preferable.
Calle,
What you describe sounds like the spacers should stay with the robot for weight and size. The inspector at your events will make the final decision once he or she examines your robot construction. Please plan accordingly.

MrForbes

14-02-2008, 08:41

This is our bumper mount system. The hex shaped standoffs are bolted to the chassis, and touch the bumper, but do not attach to it. The long coupling nuts in the corners are threaded onto the "fanged elevator bolts" that are mounted inside the bumpers. We used the long nuts to make it easier to handle the nuts without dropping them into mysterious crevices, and to have a lot more area to put the wrench on them.

D_Price

14-02-2008, 09:58

zip ties, screws, bolts, duct tape( lol bout the last one...) but it really depends on the materials of the robot and strengths

Tristan Lall

14-02-2008, 10:20

zip ties, screws, bolts, duct tape( lol bout the last one...) but it really depends on the materials of the robot and strengthsZip-ties? Those aren't allowed (as bumper mounts), you know.

<R08>, despite its occasional lack of specificity, describes a "bolt and fastener" system as the required means of attachment.

Caeruleus

17-02-2008, 20:02

What we ended up doing was using carriage bolts with a master lock on the other end of the wood to keep it in place. Keeping the fabric and pool noodles on using staples and two angled aluminum pieces.

GBIT

17-02-2008, 20:19

we drilled 1/4 inch holes in in some pieces of C channel and then droped a hinge pin in the hole attaching the C to the C of the kitbot..... it that enough of a bot and nut fasener cause it is solid.... if not were just gonna bring some 1/4 inch bolts with us