OCCRA
Go to Post This thread is a typical FRC Jurassic Park type argument: you were so busy thinking about whether you could, you didn't stop to think if you should. - barn34 [more]
Home
Go Back   Chief Delphi
CD-Media   CD-Spy  
portal register members calendar search Today's Posts Mark Forums Read FAQ rules

 subscribed threads only Play   Pause

EventByThread/PostForum
New Post
cgmv123
Today 03:40 PM
CD's Unofficial Caption Contest #741
Why waste all that candy when it could be part of their attire?
(178 views, 15 replies)
New Post
gerthworm
Today 03:32 PM
Use the I2C protocol on LabView
Check out the above links and see if they help - they should have a decent amount of info on "How to get started". If you're still stuck, it would be best if you could post code and/or the symptoms...
(187 views, 2 replies)
New Post
gerthworm
Today 03:27 PM
Robot Randomly Disconnects
The disconnect, then re-connect behavior (versus simply loosing all coms and not reconnecting) is important - it can differentiate your problem from others. Another theory - is the code experiencing...
(688 views, 10 replies)
New Post
AriMB
Today 03:24 PM
Design and Communication
I already shared it privately with Andrew, but I figure I'll share it here publicly too. I was inspired by 299's Part Indexing Sheet to create my own version, better suited to the way my team...
(2,197 views, 25 replies)
New Post
AgentSmith451
Today 02:53 PM
Destination: Deep Space Teaser
Has anyone analyzed all the "timestamp" numbers scrolling in the upper left corner? They appear to be random numbers, but they may mean something ("Be Sure To Drink Your...
(7,698 views, 79 replies)
New Post
Nick_Coussens
Today 02:45 PM
Driver Control Options for Swerve
Last year, we ran both field-centric translation and field-centric steering. This means that on our Logitech/XBOX controller, the left joystick controlled the translation, and if the driver pointed...
(146 views, 2 replies)
New Post
lbl1731
Today 02:43 PM
pic: Average Travel Distance for FRC Teams to US
I added three new sheets that do as you suggested, didn't make much of a notable difference. Correct, so for all the teams who go to the southern championship, they are traveling an average of...
(333 views, 4 replies)
New Post
pchild
Today 02:23 PM
[FF]: [FF]: [OFF] BOB 2018 Tier 2
pchild 225 9:37 9:39 AceOfSpades0 1629 9:35 9:41 SPang 384 9:33 9:43 Electronica1 9:09 9:31 9:45 tmpoles 9:12 9:29 9:47 MetroMan19 ...
(142 views, 3 replies)
New Post
pchild
Today 02:20 PM
[FF]: [OFF] BOB 2018 Tier 1
Hailey.faiella 1629 9:37 9:39 rkap51 225 9:35 9:41 nomythicalbeast 384 9:33 9:43 Golfer4646 9:09 9:31 9:45 Attention 9:12 9:29 9:47 Caleb Sykes ...
(172 views, 4 replies)
New Post
Jim Zondag
Today 02:15 PM
[OCCRA]: Starting position - Choice of the Over or the Out Area
The members of each alliance get to choose for themselves where each team will start. They must negotiate this between themselves before the match. Rule defined the rules for placement order...
(118 views, 1 replies)
New Post
GeeTwo
Today 02:08 PM
Best bandsaw for aluminum sheet?
The best way to cut something long to length is with a horizontal format saw. These have a pair of vise plates; usually one is to set the miter and the other to do the clamping. If the piece is...
(326 views, 9 replies)
New Post
Michael Corsetto
Today 01:17 PM
Registration 2019
Last year, teams found out what their first round event was ~ 1 day after the preference system closed. I don't remember when that was reflected in online event lists. -Mike
(886 views, 9 replies)
New Post
Nate Laverdure
Today 12:58 PM
Religious affiliated teams and outside mentors
Perhaps the school would consider the financial aspects of this policy. FRC is expensive . To operate sustainably, teams often must solicit large donations from corporations, nonprofit foundations,...
(1,422 views, 21 replies)
New Post
cbale2000
Today 12:48 PM
Belt Shooters
In general, wheeled shooters can run at higher RPMs than Belt shooters, so depending on the game, it might be necessary to use wheels. That said, for games that you don't have to shoot something very...
(672 views, 7 replies)
New Post
Niklas701
Today 12:11 PM
[FF]: 2019 Season Long Fantasy FIRST
Breakfast might be the most important meal of the day, nobody wants to forget Lunch but I sure do love me a good Dinner. 1. Falcon (EricH) 2. 1.21 GW (Hailey.faiella, SnapDragon, thefoxisloose,...
(2,131 views, 34 replies)
New Thread
robocodepodcast
Today 12:07 PM
RoboZone Podcast Episode #074- Rover Ruckus Part Deux
Episode Description - In this episode, we speak with FTC Students Peter and Nathan who are working diligently to plan their teams approach to meet the requirements of the FTC Rover Ruckus game. They...
(69 views, 0 replies)
New Post
JohnFogarty
Today 11:38 AM
chain in tube experiences
Third-ed? We used 221 Systems 17 tooth double sprockets on both of the teams I worked with that did CIT.
(1,064 views, 15 replies)
New Post
nuclearnerd
Today 11:36 AM
pic: Shaft Drive Bearing Blocks
Here's some new products from Actobotics that might revive this old thread:...
(8,069 views, 26 replies)
New Post
bkahl
Today 11:02 AM
Changing CD for the better.
Resource? Yes Service? No I don't think "Service" provides an appropriate connotation for the site.
(9,072 views, 102 replies)
New Post
ATannahill
Today 10:56 AM

All times are GMT -5. The time now is 04:49 PM.

The Chief Delphi Forums are sponsored by Innovation First International, Inc.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi