Go to Post What language does your programming mentor have the most experience with? That's the language you should use. - Rosiebotboss [more]
Go Back   Chief Delphi
portal register members calendar search Today's Posts Mark Forums Read FAQ rules

 subscribed threads only Play   Pause

New Post
Today 09:39 PM
Will the Ri3D Channel Still Post Other Team's Content?
I don't think this will be as big of a deal as you think. Teams having control over their own channels will be better, in my opinion, as you'll be able to dive deeper on a team you're really...
(179 views, 3 replies)
New Post
Today 09:31 PM
[FRC Blog] Join Us for a Computer Science Education Week Special Twitch Episode
I've been meaning to post this for a week, but I just wanted to say that FIRST managed to put on a good stream here. There were a few moments that were a bit awkward, (Apparently people get confused...
(1,095 views, 12 replies)
New Post
Today 09:10 PM
[FF]: [SLFF] Monterey Bay 2019 Tier 2
im saying u have many rookies who are taken on here smh smh
(826 views, 36 replies)
New Post
Citrus Dad
Today 09:02 PM
"The level playing field" in FIRST
I don't think we need to change FRC too much--Michigan has it in half of its high schools without substantial school funding in a state that is about as mixed as the US. The core is getting to the a...
(21,052 views, 212 replies)
New Post
Today 08:50 PM
[FF]: [SLFF] Monterey Bay 2019 Tier 1
LM 2073 2035 299 TLC 1671 5104 6814 1.21 GW 3128 3495 852 TBC 3256 5823 7528 JSM 192 4984 7413 TSIMFD ...
(380 views, 19 replies)
New Post
Today 08:46 PM
Cubic Hermite Spline Generation for Motion Profiling
I was looking through 254's code that did it and I tried adding that to this graph, but I was getting very wonky results and wasn't sure if I was missing something.
(243 views, 7 replies)
New Post
Today 08:36 PM
What’s Your FRC EDC?
I typically carry the following: Leatherman multitool Inkzall fine point marker Pens Pen Light Wire Stripper Ratchet Driver with 5/32, 9/64, 1/8 Hex and phillips/flathead 4 in 1 Ratchet box wrench...
(2,378 views, 26 replies)
New Post
Tyler Olds
Today 08:29 PM
FUNalysis: Analyzing this decade + giveaway 8:30pm ET!
About to start the show! Come join us, vote for which game you think is the best of the decade and win a sweet prize! https://www.twitch.tv/firstupdatesnow
(305 views, 2 replies)
New Post
Today 07:34 PM
Your dream Championship Conference session
One way to expand on this idea is to find successful teams from a variety of backgrounds and resource levels and learn what the common threads are for those teams. I think there could be a lot to...
(1,041 views, 9 replies)
New Post
Today 07:25 PM
Software for REV Brushless motor
Thanks Andrew
(615 views, 2 replies)
New Post
Today 07:13 PM
FRC Blog - 2019 Motor Controllers and MXP
Thank you so much!! I've been persistent in asking about this feature for a while, but the results are absolutely amazing!
(48,219 views, 302 replies)
New Post
Today 06:51 PM
CAN Connector or Micro Fit Molex Connectors
This is what we use on 2655: https://www.amazon.com/Hilitchi-300Pcs-Housing-Terminal-Connector/dp/B0188YKCFC/ref=sr_1_7?ie=UTF8&q id=1545176977&sr=8-7&keywords=jst+conne ctor+kit The connectors are...
(1,498 views, 23 replies)
New Thread
Today 05:46 PM
pic: 694 Getting In On The Action
(197 views, 0 replies)
New Post
Today 05:44 PM
Electrical Boards and wire management
My team uses them and they make things alot more organized.
(1,507 views, 20 replies)
New Post
Today 05:32 PM
Versaplanetary Vs 57 Sport
Did you refer to the VEX gear ratio chart vs. load? It tells you what combination is recommended. I saw a lot of 10:1's fail that year during rope climbing because of that.
(4,745 views, 52 replies)
New Post
Michael Corsetto
Today 04:56 PM
Introducing the new TubeMagic Fixturing System
We just ordered 3 of these for our X8 Omio. Hope to run most of our tubes with this jig this coming season. We had an in-house design that was showing promise and able to run 6 tubes on the X8, but...
(2,524 views, 18 replies)
New Post
Today 04:56 PM
local robotpy docs - how?
Thanks - will look at the post-process option
(94 views, 2 replies)
New Thread
Today 04:39 PM
Cyber Tribe 4020 LabView Code 2018
This is Cyber Tribe 4020's code from the 2018 competition season. Included in the folder is our Driver Station, LabView Path Manager, Robot Code, and Vision Software as well as 3D objects. In our...
(53 views, 0 replies)
New Post
GDG 2337
Today 03:51 PM
chain in tube experiences
We’ve also found the exact c-c distance is not an exact science, at best the various models get you close. From experience, VexPro and AndyMark sprockets and chains are not the same. If you’re...
(4,410 views, 33 replies)
New Post
Today 03:35 PM
[BobTrajectory] Announcing Version 1.0!
We ran BobTrajectory last season and it worked great for us. The new improvements are a big update, thanks for putting in the work to make this better for the community.
(822 views, 6 replies)

All times are GMT -5. The time now is 10:28 PM.

The Chief Delphi Forums are sponsored by Innovation First International, Inc.

Powered by vBulletin®
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi