![]() |
Wiring the turret
Does anyone know how to wire a rotating turret? We were thinking of a spring loaded reel that could pay out or retract wire so we don't have 3ft of slack hanging off of our motors. Does anybody have any ideas?
Thanks, Team 612 |
Re: Wiring the turret
How far does your turret rotate and why? It will help figure out how to run wires.
|
Re: Wiring the turret
Quote:
|
Re: Wiring the turret
It will rotate a maximum of 270 degrees.
|
Re: Wiring the turret
How about:
Quote:
|
Re: Wiring the turret
Our elevator system is in the middle of the of the circle. If we were to do that:
Originally Posted by DonRotolo View Post Slip rings are to be avoided where possible. Run your wires via the center of the rotating circle. Just leave considerable slack so the wires don't twist excessively, and limit how many times you can turn the circle before having to turn the other way. 360 degrees either direction is not at all difficult. Then our balls would hit the wiring |
Re: Wiring the turret
Quote:
This would be difficult to do if balls are going through the center of the turret. Have you considered pre-coiled wire? If you anchor it to take the stress of the motor leads, it would stretch during rotation and relax during counter rotation. |
Re: Wiring the turret
Quote:
|
Re: Wiring the turret
Alway make sure there is some kind of mechanical stop that limits the turret from rotating further than the wires can go without hurting the motors or other systems. So if you go 270deg stop the turret from going 271+deg. It can be a rope, cable, or some bolts that hit some part of the turret. Anything to keep from stress on the wires to the motors or sensors.
|
Re: Wiring the turret
Quote:
|
Re: Wiring the turret
What options do we have if our turret rotates all the way around, 360 degrees (no limits)?
|
Re: Wiring the turret
Attach all the wires on the turret to a common point on the turret, and run them all together from there (you can use zip ties, wire mesh, split tubing, or other ways to do this). From that single point, you'll have an attachment point that closely matches it when the turret it halfway through its rotation. At this halfway point, you'll have the most loose wire to deal with - rotating either direction from there will pull the wire and decrease/eliminate looseness as you get to the two extremes.
Once at that point, the easiest way I can think of to manage the wire is to have it spring loaded in some fashion. This could be as simple as a rubber band that helps provide a little tension - however you want to make sure you aren't stressing the wire (having some well mounted cable running along with your wire can help with this - the stress will be on the cable, and the cable will help direct the wire). Regardless of the design you come up with, make sure the wire moves through a "safe" zone the entire time - and area with no sharp edges, and nothing but smooth curves. The last thing you want is for a sharp edge on the turret to cut through your wire! Another possible solution: run a post that goes up and over your turret (probably behind the turret in the area it can't rotate to face). You can run the wires along there, then drop them straight down onto the turret. That should allow maximum rotation with minimal loose wiring. |
Re: Wiring the turret
Thanks we will try it out!
|
Re: Wiring the turret
Quote:
We did look into slip rings, and they were extremely expensive. I'm not sure there's a huge benefit to having unlimited rotations anyway. As long as you have 370+ degrees of rotation, you will be able to aim in any direction. Simply "untwist" as needed. |
Re: Wiring the turret
Quote:
|
| All times are GMT -5. The time now is 19:48. |
Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi