Chief Delphi

Chief Delphi (http://www.chiefdelphi.com/forums/index.php)
-   General Forum (http://www.chiefdelphi.com/forums/forumdisplay.php?f=16)
-   -   What is wrong? [HELP] (http://www.chiefdelphi.com/forums/showthread.php?t=104356)

Andrew Lawrence 08-03-2012 08:59

What is wrong? [HELP]
 
Our final, final robot weighs around 85 pounds, WITH the electronics. For years, 256 has had to swiss cheese our robots to make the legal and under the weight limit, however this year is different, and we didn't do it on purpose.

I don't think we forgot anything:

-Sturdy drivetrain
-sturdy frame
-articulating ball shooter
-accurate bridge actuator mechanism
-very well working ball intake
-very well working ball elevator

What I don't get is how we have managed to come under weight. It is our first time making a custom chassis and superstructure, but I didn't think that could loose us so much. I'm afraid something on our robot is under-built, and too weak, but everything is stronger than me in some cases.


What should I do? :confused:

Our scale works perfectly, and since we were also unsure, we used another one we never used before and got the same weight

fox46 08-03-2012 09:05

Re: What is wrong? [HELP]
 
I would invest in a new scale.

quinxorin 08-03-2012 09:05

Re: What is wrong? [HELP]
 
Strap on 33 lbs. An underweight robot makes it difficult to balance with other teams on the coopertition bridge.

Peter Matteson 08-03-2012 09:08

Re: What is wrong? [HELP]
 
Stop bragging about being under weight. :rolleyes:

Seriously though not knowing the details of what your robot looks/performs like it's hard to answer that question. I can list possible places you could have missed but I need more info.

Is your frame too thin/weak?

Do you have normally have pnumatics but not this year?

Are there fewer sensors?

Did you use a different drive system than normal?

Is your robot really short?

did you use just the smallest motors in the lkit?

Are you lacking protection/shielding around your electronics to prevent balls from sticking in your robot?

Is your robot not the full 28"x38" that you're used to?

Just some stuff I though of quick.

pyroslev 08-03-2012 09:10

Re: What is wrong? [HELP]
 
ASAP, weigh it on a scale that you've never seen before, just to cover your bases.

Beyond that, add weight as others have said. That or make yourself the robot that aids the balancing while popping the last shot off.

And nothing wrong with being that far under.

Andrew Lawrence 08-03-2012 09:13

Re: What is wrong? [HELP]
 
Quote:

Originally Posted by Peter Matteson (Post 1140947)
Stop bragging about being under weight. :rolleyes:

Seriously though not knowing the details of what your robot looks/performs like it's hard to answer that question. I can list possible places you could have missed but I need more info.

Is your frame too thin/weak?

No, it's sturdy

Do you have normally have pnumatics but not this year?

Actually....yes! Come to think of it, we lack pneumatics this year

Are there fewer sensors?

Just about the same

Did you use a different drive system than normal?

4WD wide instead of a 6WD long

Is your robot really short?

Not really.

did you use just the smallest motors in the lkit?

Nope.

Are you lacking protection/shielding around your electronics to prevent balls from sticking in your robot?

Right now, yes, but the one we built is already factored into the weight

Is your robot not the full 28"x38" that you're used to?

it is, although it's a welded frame, so a lot of it is opened up.

Just some stuff I though of quick.

Thanks for the help! I'm thinking it's the lack of pneumatics and lighter frame, though I never thought the combination of the two would loose us 30 pounds..

Nor my new problem: What to do with those 30 pounds? The bottom of our robot is mostly hollow to allow our intake to pick up from both sides, so it's hard to put things places.

Wayne Doenges 08-03-2012 09:30

Re: What is wrong? [HELP]
 
Have your programmer add more 1's into the program an remove as much of the 0's as possible :rolleyes:

SenorZ 08-03-2012 10:18

Re: What is wrong? [HELP]
 
At our pre-bag scrimmage, without our shooter on, but WITH our bumpers, our robot was 81lbs! It was VERY hard to control.
With the shooter (and no bumpers), it should be around 90, 95. Still light. I think not using pneumatics is a big deal for us.

MrForbes 08-03-2012 10:24

Re: What is wrong? [HELP]
 
We managed to avoid that problem by welding up a nice 27 pound steel frame for the bottom of the robot. And we have about 10 lbs of pneumatics, too.

One rookie Tucson team we've been following has a really light robot like that, they came up with a neat design for their sheet metal sponsor to make, and their robot is somewhere around 85 lbs.

Since the bridge causes short wide robots some issues, especially when there are balls under the end of the bridge, you might see if there is some heavy thing you could add to the bottom that would make bridge climbing easier, and flipping less likely. We're looking into this for our robot.

Blackphantom91 08-03-2012 10:28

Re: What is wrong? [HELP]
 
There was a team at kc that put a steel plate into their robot chassis which helped them not become so tipsy during comp it worked very well for them. Bridge balancing does become harder without some "good weight"

Ryan Caldwell 08-03-2012 11:54

Re: What is wrong? [HELP]
 
This sounds like a great opportunity to try to lower and center your CG. We did something very similar weighed in at 93lbs at bag, so during un-bag we added steel plate to beef up our frame in the 4 corners as low as possible. Moving weight out the the edge of the frame helps improve your stability much like a tightrope walker with a long weighted pole.

I'd agree it's beneficial to be closer to 120-lbs to ease balancing multiple robots.

Nemo 08-03-2012 16:03

Re: What is wrong? [HELP]
 
Quote:

Originally Posted by Blackphantom91 (Post 1140988)
There was a team at kc that put a steel plate into their robot chassis which helped them not become so tipsy during comp it worked very well for them. Bridge balancing does become harder without some "good weight"

I put a picture of this steel plate on flickr, and it is linked in the robot showcase thread I just created:

http://www.chiefdelphi.com/forums/sh...hreadid=104366

Andrew Lawrence 08-03-2012 20:38

Re: What is wrong? [HELP]
 
Thanks all for your help! I really appreciate it. :D An underweight robot is just as bad as an over weight one, so I'm glad we'll be able to beef up our machine.

We decided to use the extra weight to lower and center our CG, and well as make our robot look really cool. :cool:

Andrew Lawrence 08-03-2012 23:16

Re: What is wrong? [HELP]
 
Quote:

Originally Posted by Garret (Post 1141240)
I would still check on another scale if at all possible, its never fun to go in thinking you are underweight only to find out on day 1 of the tournament that your scale was bad and way off. I know from experience this year...

We've tested it on a total of 3 different scales as of today. All 3 gave us the exact same measurement, +/- a .5 lb.

Ankit S. 09-03-2012 00:25

Re: What is wrong? [HELP]
 
Quote:

Originally Posted by SuperNerd256 (Post 1140942)
Our final, final robot weighs around 85 pounds, WITH the electronics. [/b]

Not sure if I told you already, but we are about 15 under. We are definitely gonna bring some thick steel to attach on Thursday.

As for where, you could attach it to the very bottom of your robot, sort of like a baseplate. This should not change much, as it would be low enough to allow balls to pass over without any problem.

You could always just put on one of those half-freshmen that lay around after accidents... :ahh:


All times are GMT -5. The time now is 07:20.

Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi