![]() |
ideas for a strong hook
Our team spent a lot of time searching the internet to find a hook to hook onto the horizontal bar that could hold over 100 lbs. We didn't have much success.
Can anyone give ideas where to buy one or how to make one? We are a young team, so we don't have much fabrication experience. It would be better if we could buy one then figure out how to attach it to our ascension mechanism (which we are still working on too). Right now the hooking spot is a horizontal piece of steal, so if the hook was connected to a flat piece where we could just screw it onto our steal plate, that would be perfect! Thanks! |
Re: ideas for a strong hook
|
Re: ideas for a strong hook
Bent aluminum rod worked for us in '10. We fell once but it was because of a bent eye hook, never had a problem with the actual hook.
|
Re: ideas for a strong hook
We went with a modified shark hook in 2010; it was fashioned from some black steel IIRC. Worked like a beaut.
|
Re: ideas for a strong hook
If you make something from scratch, use extremely few parts, let's chances for failure.
May I suggest Lexan, or square tubing.:] |
Re: ideas for a strong hook
Thank you for these ideas, keep them coming if you can :]
|
Re: ideas for a strong hook
I have a vise, torch, and big hammer in my shop, so I could probably make a hook from steel that would work. But I don't know what you have available.
If you have a jig saw or band saw, you could cut a hook from sheet aluminum rather easily. You might need to order the aluminum though, if you live in a small town. 1/8" aluminum will probably work, if you design the hook so it has sufficient width. Also, not having any idea what you are going to attach the hook to, it's hard to be more specific about how you could make the hook. and plywood works too! http://www.chiefdelphi.com/forums/sh...d.php?t=111128 |
Re: ideas for a strong hook
It's not too hard. Bend some aluminium rod in a pipe bender, mill a hook out of some 1/4" plate, make some out of thinner plate and standoffs... whatever works for you. I bet you could do it with Kitbot frame material.
|
Re: ideas for a strong hook
Repurposing some C-clamps might be a reasonable approach. Particularly ones similar to this http://www.sweetwater.com/store/detail/CClamp
Or use them as inspiration for building your own. Greg McKaskle |
Re: ideas for a strong hook
Here's a fairly simple one to make.
|
Re: ideas for a strong hook
If you decide to make your own (I personally wouldn't because I was also an eyewitness to the incredible badassery of a shark hook - it's very light and it's just about the right size for the pipes once you grind the barb off), you can easily model a hook in any material in either Solidworks or Inventor and then run a simulation to see if it would yield under the 100+ pounds of force. I'd be happy to explain the process if you're curious.
|
Re: ideas for a strong hook
Again, thank you all very much. Additional ideas always welcome.
As we try something and it doesn't work, this gives us additional ideas to continue working with. |
Re: ideas for a strong hook
We prototyped a hook out of 1/4" 6061 aluminum plate, it easily supported a robot equivalent of weight.
|
Re: ideas for a strong hook
Modify a climbing carabiner, large size, by removing the gate or the locking mechanism of the gate (depending on whether you want to lock onto the bar or use the hook elsewhere). I've seen teams lift robots with them before. If they can hold a 200lb human, they should be able to hold a 150lb robot--just make sure you get one rated for that weight.
As an added bonus, they're not going to be terribly expensive. |
Re: ideas for a strong hook
Carabiners are traditionally rated in kN (approximately 225 lbs). The ratings are specific along the different parts of the carabiner, if you are going this route talk to your local outdoor store and see what they have.
|
| All times are GMT -5. The time now is 22:47. |
Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi