Chief Delphi

Chief Delphi (http://www.chiefdelphi.com/forums/index.php)
-   Technical Discussion (http://www.chiefdelphi.com/forums/forumdisplay.php?f=22)
-   -   How is 54" size limit being inspected? (http://www.chiefdelphi.com/forums/showthread.php?t=114973)

Bob Steele 13-03-2013 23:52

How is 54" size limit being inspected?
 
We aren't competing until the 4th week ( and the 5th and the 6th)
Can anyone enlighten me as to how a team needs to confirm that they meet the 54" rule?

Are inspectors asking this question? Are they asking a team to expand to its full size and measuring..??

just wondering.
We have a CAD drawing that shows our extensions to give an inspector to show how we meet the rule.

thanks!

Gregor 13-03-2013 23:54

Re: How is 54" size limit being inspected?
 
Quote:

Originally Posted by Bob Steele (Post 1247940)
We aren't competing until the 4th week ( and the 5th and the 6th)
Can anyone enlighten me as to how a team needs to confirm that they meet the 54" rule?

Are inspectors asking this question? Are they asking a team to expand to its full size and measuring..??

just wondering.
We have a CAD drawing that shows our extensions to give an inspector to show how we meet the rule.

thanks!

We printed off a few cad models to prove that we didn't exceed 54". The inspector said he appreciated this. To manually check, he took a measuring tape, and measured from furthest point to furthest point.

BigJ 13-03-2013 23:54

Re: How is 54" size limit being inspected?
 
At Northern Lights we had to declare our maximum extensions so that they could make the refs aware. It might have been measured because the person with the exact answer was not there but the way the conversation was going it might not have been measured if the answer was confident (the parts were extended, though). I am guessing if the number given did not sound realistic a measuring would have happened anyway.

Darren Collins 14-03-2013 00:02

Re: How is 54" size limit being inspected?
 
In Portland, the inspectors had a 54" circle taped on the floor. The robot was placed in the circle. Any mechanisms or appendages were extended to ensure that the 54" cylinder wasn't breached. They also used a square made of wood and placed it at the edge of the circle to see if anything above the floor broke the cylindrical barrier.

rsisk 14-03-2013 00:04

Re: How is 54" size limit being inspected?
 
I ask teams to extend any components that go outside the frame perimeter then pull out a measuring tape.

Gregor 14-03-2013 00:06

Re: How is 54" size limit being inspected?
 
Quote:

Originally Posted by rsisk (Post 1247949)
I ask teams to extend any components that go outside the frame perimeter then pull out a measuring tape.

Same thing happened at our inspection, but that doesn't measure a true 54" diameter in most cases.

Grim Tuesday 14-03-2013 00:10

Re: How is 54" size limit being inspected?
 
Quote:

Originally Posted by Gregor (Post 1247943)
We printed off a few cad models to prove that we didn't exceed 54". The inspector said he appreciated this. To manually check, he took a measuring tape, and measured from furthest point to furthest point.

This is not the correct way to check. Our robot (see signature) is very close to being over the 54" limit, I think we were within about 1/2 an inch. The maximum point method will pass illegal robots. See the below picture for an explanation:

http://i.imgur.com/pDNlj09.jpg

At Fingerlakes, after an Inspector tried this method, we informed him why it was wrong and they pulled out a prinout of a 54" circle, which they projected upwards with an ruler. This seems like the correct method to use.

Gregor 14-03-2013 00:21

Re: How is 54" size limit being inspected?
 
Quote:

Originally Posted by Grim Tuesday (Post 1247954)
This is not the correct way to check. Our robot (see signature) is very close to being over the 54" limit, I think we were within about 1/2 an inch. The maximum point method will pass illegal robots. See the below picture for an explanation:

http://i.imgur.com/pDNlj09.jpg

At Fingerlakes, after an Inspector tried this method, we informed him why it was wrong and they pulled out a prinout of a 54" circle, which they projected upwards with an ruler. This seems like the correct method to use.

Agreed, that makes much more sense. We never got pulled to the printout at Finger Lakes though. I was surprised that this wasn't standardized between different regional, but how can the cylinder not be measured the same way within a regional?

s_forbes 14-03-2013 00:30

Re: How is 54" size limit being inspected?
 
Quote:

Originally Posted by Grim Tuesday (Post 1247954)
This is not the correct way to check. Our robot (see signature) is very close to being over the 54" limit, I think we were within about 1/2 an inch. The maximum point method will pass illegal robots. See the below picture for an explanation:

http://i.imgur.com/pDNlj09.jpg

At Fingerlakes, after an Inspector tried this method, we informed him why it was wrong and they pulled out a prinout of a 54" circle, which they projected upwards with an ruler. This seems like the correct method to use.

The point to point method will still work if the inspector measures from the bumper corner to the mechanism corner (at least for most cases), but I could see this being missed. EDIT: doh, math. No it wont.

I was looking forward to seeing a cylindrical sizing box this year, but given the quality of sizing boxes in the past, I probably would have hated it. :rolleyes:

Radical Pi 14-03-2013 00:37

Re: How is 54" size limit being inspected?
 
Quote:

Originally Posted by Gregor (Post 1247966)
Agreed, that makes much more sense. We never got pulled to the printout at Finger Lakes though. I was surprised that this wasn't standardized between different regional, but how can the cylinder not be measured the same way within a regional?

As I understand it, the measuring tape was supposed to be used to get a rough idea of whether they were at risk of breaking the cylinder. They subtracted a portion from the 54" to account for the circular nature of the cylinder and measured that. If you were close, you'd get pulled to the real circle for a closer inspection.

Gregor 14-03-2013 00:44

Re: How is 54" size limit being inspected?
 
Quote:

Originally Posted by Radical Pi (Post 1247971)
As I understand it, the measuring tape was supposed to be used to get a rough idea of whether they were at risk of breaking the cylinder. They subtracted a portion from the 54" to account for the circular nature of the cylinder and measured that. If you were close, you'd get pulled to the real circle for a closer inspection.

We were right on the verge as shown in our CAD, we were within 1/2" of 54". We clearly told the inspector this, which is why I'm confused.

Jaxom 14-03-2013 00:58

Re: How is 54" size limit being inspected?
 
Quote:

Originally Posted by Bob Steele (Post 1247940)
Are inspectors asking this question? Are they asking a team to expand to its full size and measuring..??

We're certainly supposed to be asking this; it's a specific item in the inspection checklist. If this doesn't come up during your inspection ask the inspector why not.

At Hub City, afaik we only had one robot that had any possibility of an issue with this. I happened to be the inspector; by mutual request (team and the inspectors) we went through a reasonably exhaustive series of measurements to determine that there was no problem. We didn't have any kind of circle drawn to do this, but a tape measure and a little math did the trick.

Ask me tomorrow about GKC. At early check-in tonight I didn't see any robots that might have a problem with this sizing but I wasn't particularly looking for it, either.

dtengineering 14-03-2013 02:15

Re: How is 54" size limit being inspected?
 
What we can be sure of is that if any two points on the robot are more than 54" apart then they violate the rule.

There are also many machines that clearly are not in violation of the rule.

That leaves some "borderline" machines, but likely not many. It might be easiest to tape off a 54" circle, tangent to a wall, extend the appendage to touch the wall, and then place the robot inside the circle.

Just so long as we don't have that silly hoop back again. What year was it that we had the big hula hoop?

Jason

Tristan Lall 14-03-2013 02:17

Re: How is 54" size limit being inspected?
 
Quote:

Originally Posted by dtengineering (Post 1247999)
What we can be sure of is that if any two points on the robot are more than 54" apart then they violate the rule.

Unless they're not in a plane perpendicular to the axis of the cylinder....

tickspe15 14-03-2013 02:45

Re: How is 54" size limit being inspected?
 
In Portland there was a circle taped on the ground to set the robot in. Then a vertical board was run around the circle to make sure that no part of the robot extended out of the circle. I think they will use the same technique in ellensburg.


All times are GMT -5. The time now is 18:15.

Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi