Chief Delphi - cRIO image 2012

Chief Delphi (http://www.chiefdelphi.com/forums/index.php)

- FRC Control System (http://www.chiefdelphi.com/forums/forumdisplay.php?f=176)

- - cRIO image 2012 (http://www.chiefdelphi.com/forums/showthread.php?t=119650)

Invictus3593

24-09-2013 17:28

cRIO image 2012

So, we imaged our 8-slot cRIO from 2011 to the v47 image. When we start run our robot, the robot doesn't want to realize there is a solenoid module there, even though it does see the module when imaging. We think that the image for the cRIO is the problem, since we had no problems with the 2012 image that used runtime 11, and in the new image it has runtime 12. So does anybody have a non-2013 version of the image for the 8-slot cRIO? Should just be a .zip pack, right?

Joe Ross

24-09-2013 18:53

Re: cRIO image 2012

Did you move the solenoid module to the correct slot for the new image? The imaging tool shows you the correct slots.

Invictus3593

24-09-2013 23:33

Re: cRIO image 2012

Quote:

Originally Posted by Joe Ross (Post 1292854)

Did you move the solenoid module to the correct slot for the new image? The imaging tool shows you the correct slots.

Yeah, it's in the right one. We even tried putting it in the old slot just to be sure :confused:

We get all green cards in the imaging tool when that starts up

RufflesRidge

25-09-2013 06:19

Re: cRIO image 2012

Has the code been updated to the new module numbering scheme? It should say module 1 or 2, not Slot 8.

Invictus3593

25-09-2013 12:54

Re: cRIO image 2012

Quote:

Originally Posted by RufflesRidge (Post 1292901)

Has the code been updated to the new module numbering scheme? It should say module 1 or 2, not Slot 8.

Yeah, we tried using both "Solenoid Module 1" and "Solenoid Module 2". It may just be our cRio:/

We emailed NI to see if they have a previous version of the image with runtime 11 beacuse that's what worked before, then we would just have to use the program written in labview 2011.

Joe Ross

25-09-2013 13:20

Re: cRIO image 2012

Can you post your code? Is there an error message about the solenoid module, or does it just not work?

Invictus3593

01-10-2013 08:58

Re: cRIO image 2012

Quote:

Originally Posted by Joe Ross (Post 1292963)

Can you post your code? Is there an error message about the solenoid module, or does it just not work?

It just doesn't work. We've programmed this bot a million times because it's just a compressor, two solenoids and drive. The only problem is when we re-imaged with the 2013 image.

Before we imaged, it said that it had runtime 11, now it has 12; would that have anything to do with it?

PS: this is not a competition bot, it's a t-shirt cannon for football games

MechEng83

01-10-2013 09:36

Re: cRIO image 2012

We ran into this exact same issue -- for a t-shirt cannon robot too!

Once we reimaged the 8 slot cRIO with the 2013 tool, it required that we moved the modules to the same configuration as the 4 slot, and it worked for us.

Invictus3593

01-10-2013 14:17

Re: cRIO image 2012

Quote:

Originally Posted by MechEng83 (Post 1294008)

Once we reimaged the 8 slot cRIO with the 2013 tool, it required that we moved the modules to the same configuration as the 4 slot, and it worked for us.

We had only tried re-imaging with the modules in the old configuration, we'll try the whole process in the new one and see if that works!

All times are GMT -5. The time now is 19:15.