Chief Delphi

Chief Delphi (http://www.chiefdelphi.com/forums/index.php)
-   Technical Discussion (http://www.chiefdelphi.com/forums/forumdisplay.php?f=22)
-   -   1/2 hex shaft coupling (http://www.chiefdelphi.com/forums/showthread.php?t=125277)

johey 26-01-2014 09:39

1/2 hex shaft coupling
 
We have been looking around and we can't find 1/2'' hex shaft coupling.

Does anyone know where we could find a coupling to fit two 1/2'' hex shaft together?

Thanks
Rookie team Carnicas 4952

Richard Wallace 26-01-2014 09:50

Re: 1/2 hex shaft coupling
 
You could get two of these and bolt them together.

Tem1514 Mentor 26-01-2014 09:55

Re: 1/2 hex shaft coupling
 
1 Attachment(s)
You can always make one by drilling a hole in a piece of bar stock so that the HEX will fit in tightly then add set screws or even pin the Hex in place.

Of course a lathe will really help. The picture is taking a square block and making it round for all the poly cord pulleys we need on this years bot.

xForceDee 26-01-2014 11:45

Re: 1/2 hex shaft coupling
 
Quote:

Originally Posted by Richard Wallace (Post 1332640)
You could get two of these and bolt them together.

How would you go about attaching the hubs to the shaft? Are you thinking tap a hole or two and use setscrews?

sanddrag 26-01-2014 12:09

Re: 1/2 hex shaft coupling
 
Small Parts used to have things like this, but I can't find it anymore now that it's become Amazon Supply.

nixiebunny 26-01-2014 12:26

Re: 1/2 hex shaft coupling
 
You might be able to find a piece of C channel that fits snugly on one side of the hex shaft. Cut two lengths of it, place them on either side of the butted shafts, drill holes through the channels and shaft as a sandwich, bolt it all together.

If you can't find the channel, then find a person with a brake and make some yourself. Use 60 degree bends.

Qbot2640 26-01-2014 12:28

Re: 1/2 hex shaft coupling
 
How much torque / tension does it have to withstand? I've 3D printed hex "sleeve" that we plan to use as spacers - but it is incredibly strong - even when printed with a relatively low infill.

Michael Yeh 26-01-2014 12:45

Re: 1/2 hex shaft coupling
 
http://www.vexrobotics.com/vexpro/ha...washers-g.html
They're available up to 2" long and super cheap, I've considered putting setscrews in them for couplings but never actually tried it.
It might not be strong enough for your application though.

BJT 26-01-2014 16:03

Re: 1/2 hex shaft coupling
 
One of our students suggested we cut the end off a deep wall 1/2inch socket and put some set screws in it. Should work.

Bald & Bearded 26-01-2014 18:21

Re: 1/2 hex shaft coupling
 
Joehy:
If anyone near you has a 3D printer you can print one of these from
Thingiverse: http://www.thingiverse.com/thing:229161

Best to print with Nylon if they have an all metal hot end.

Tem1514 Mentor 26-01-2014 18:52

Re: 1/2 hex shaft coupling
 
Quote:

Originally Posted by BJT (Post 1332785)
One of our students suggested we cut the end off a deep wall 1/2inch socket and put some set screws in it. Should work.

Very good idea only problem is the socket has been heat treated and will be very hard to drill and tap unless you are using carbide tooling.

thefro526 26-01-2014 19:26

Re: 1/2 hex shaft coupling
 
Last year, we bought one of these: http://www.mcmaster.com/#2424k14/=qfauwg and ran a broach through it. I'm not entirely sure how well it will perform as a power transferring connection, but it connects two shafts just fine. Initially, we planned on running power through that coupling and then onto our climbing mechanism, but that never panned out, so instead, it just connected the two 'stub' shafts that our arm pivoted on.

In a pitch, I've also seen teams take a hex hub from AndyMark, drill two holes in it for set screws and use that to connect two shafts. Works just fine, but isn't 'pretty' fix unless you take the bolting surface off.

Quazar 26-01-2014 20:44

Re: 1/2 hex shaft coupling
 
We are using Hex-hole sleeves, purchased from SDP/SI; just search for part number "A 7C20-08".



The shafts we are joining are captive, and the sleeve is constrained between hubs, so we aren't bothering with set-screws, though it would be pretty easy to drill and tap for set screws if desired.

They are very solid and are a slip-fit on the VEXpro hex axles. They are not particularly cheap or light though. If you need them to be light, and you don't mind spending for a hex broach, you may be better off broaching round shaft couplers as thefro526 describes.

Cheers,
- Dean

roystur44 26-01-2014 21:53

Re: 1/2 hex shaft coupling
 
You could use a lathe and drill the ends with a .251 drill and use a dowel pin and
and press it together or weld it

Aren_Hill 26-01-2014 22:09

Re: 1/2 hex shaft coupling
 
Here

217-3430

The WCP Colson Live hub has a 1.875" deep 1/2" HEX in it,
This and some pins may suffice.


-Aren


All times are GMT -5. The time now is 19:55.

Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi