![]() |
2583's Octocanum Modules
This year 2583 is using Octocanum for the first time ever
4x1.5" inch Colsons geared to 7 fps and 4" Vex mecanum wheels geared to 20.5 fps (around 15 fps forward after loss of top speed from mecanum) Gears inside the module get the reduction without any belts or tensioning One CIM per module 4.1 lbs per module without CIM (6.9 with CIM) Each side of the octocanum is activated by one 1.0625 bore piston pushing in between them, total of two pistons Traction wheels deploy on the outside to make it impossible to turn for straight driving in autonomous and to prevent being pushed while shooting All comments and critiques are appreciated ![]() ![]() ![]() |
Re: 2583's Octocanum Modules
Holy image size, Batman!
Is that a mounting hole for a CIM I see there in the side? |
Re: 2583's Octocanum Modules
yes it is,
a CIM with a 14 T gear mounts to the side there (fixed the image size) |
Re: 2583's Octocanum Modules
Depending on gear reduction, frame and power (# of motors) you may be able to turn.
Our LogoMotion octanum, with a cim & 775 on each transmission, actually handled quite well in traction mode, even though it was in 'long' orientation with traction wheels on the ends. |
Re: 2583's Octocanum Modules
These are pretty cool. They are also the first cantilevered meccanum wheels I've ever seen (not that there's anything wrong with that).
|
Re: 2583's Octocanum Modules
Cantilevered octacanum is far from impossible, but you've got to think seriously about how the module is supported and what moments you are putting on the pivot shaft. How is this attaching to the frame?
|
Re: 2583's Octocanum Modules
It pivots around the hole at the top of the module and the standoff on the mecanum side is where the piston will push/pull
I have attached a few screenshots of the side rail including two modules to help visualize it ![]() ![]() ![]() ![]() |
Re: 2583's Octocanum Modules
I like your single piston switching method. Do you have a hard stop for the modules so that the piston doesn't take the path of least resistance and kick one module out, leaving the other un-switched?
|
Re: 2583's Octocanum Modules
Its hard to see but if you look at the side view, all the way on the outside there are two 1/2 inch holes and right above those there are two small holes next to the vertical line of three holes.
A bolt/standoff through that hole will act as a hard stop for the module |
Re: 2583's Octocanum Modules
Here are some screenshots of the two positions that the hard stops will create when the piston extends/retracts
![]() ![]() |
Re: 2583's Octocanum Modules
Have you done the math to make sure your modules will actually shift? We are moving to 4 1.5" diameter cylinders because our 4 1 1/16" were having problems. Our setup is different than yours but it seems like you will have a hard time lifting your whole robot.
|
Re: 2583's Octocanum Modules
Quote:
It's hard to see how much mechanical advantage they have--looks like close to none--but 2 x pi x (1.5 in/2)^2 x 60 psi = 212 lbs; well more than enough. |
Re: 2583's Octocanum Modules
Quote:
|
Re: 2583's Octocanum Modules
Quote:
|
Re: 2583's Octocanum Modules
Quote:
2 x pi x (1.0625 in/2)^2 x 60 psi = 106 lbs, which is well below comfort without a 2:1 or better mechanical advantage. |
| All times are GMT -5. The time now is 23:02. |
Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi