Chief Delphi

Chief Delphi (http://www.chiefdelphi.com/forums/index.php)
-   Pneumatics (http://www.chiefdelphi.com/forums/forumdisplay.php?f=54)
-   -   Pneumatic Tank Restrictions (http://www.chiefdelphi.com/forums/showthread.php?t=132198)

Lemon 05-01-2015 22:37

Pneumatic Tank Restrictions
 
After looking through the manual, I couldn't find any restriction as to the manufacture of pneumatic tanks used for the systems. Specifically, to the best of your knowledge is there anything that would restrict us from using a Viair half gallon or gallon metal tank?

http://www.viaircorp.com/05gallon.html

orangemoore 05-01-2015 22:40

Re: Pneumatic Tank Restrictions
 
As far as I have read the only restriction on tanks is it must be rated 125 psi or above and they cannot be the White CLIPPARD Plastic Air tanks.

Quote:

R66
I. Pneumatic storage tanks (with the exception of White Clippard tanks P/N: AVT-PP-41)
Quote:

R64 All pneumatic items must be COTS pneumatic devices rated by their manufacturers for working pressure of at least 125psi (with
the exception of R66-D).

AllenGregoryIV 05-01-2015 22:47

Re: Pneumatic Tank Restrictions
 
Quote:

Originally Posted by orangemoore (Post 1422411)
As far as I have read the only restriction on tanks is it must be rated 125 psi or above and they cannot be the White Plastic Air tanks.

Just for clarification. Only White CLIPPARD plastic air tanks are illegal. There are a variety of plastic air tanks that happen to also be white. Those are still legal.

Chris_Ely 06-01-2015 10:29

Re: Pneumatic Tank Restrictions
 
One thing to keep in mind is that the typical compressors used in FRC only have a 9% duty cycle. They get very hot with prolonged use, such as filling a large tank. I would suggest mounting one of the large fans from the KOP next to the compressor to help cool it.

rich2202 06-01-2015 10:44

Re: Pneumatic Tank Restrictions
 
Quote:

Originally Posted by AllenGregoryIV (Post 1422416)
Just for clarification. Only White CLIPPARD plastic air tanks are illegal. There are a variety of plastic air tanks that happen to also be white. Those are still legal.

Further clarification: The specified tanks had failure problems, and that's why they are not allowed. FRC has nothing against white tanks, plastic tanks, or other Clippard tanks.

rich2202 06-01-2015 10:49

Re: Pneumatic Tank Restrictions
 
Quote:

Originally Posted by Chris_Ely (Post 1422657)
One thing to keep in mind is that the typical compressors used in FRC only have a 9% duty cycle.

I saw a team last year use a large tank. Note: It has to be pressurized with a legal Compressor (check the specifications for compressors). They charged it with an off-bot compressor (heavy duty legal compressor). It took 2-3 minutes to charge the tank.

seg9585 06-01-2015 17:30

Re: Pneumatic Tank Restrictions
 
Here's a thought: could the tanks be pressurized while physically detached from the robot (still pressurized by one legal compressor), then installed on the field to comply with transport dimension rules?

I envision a propane-tank-sized accumulator fit to the side of the bot, pressurized off the bot and closed with a valve, then attached to the pressure loop on the bot during the 1-minute field prep.

Mark Sheridan 06-01-2015 17:39

Re: Pneumatic Tank Restrictions
 
Quote:

Originally Posted by seg9585 (Post 1423059)
Here's a thought: could the tanks be pressurized while physically detached from the robot (still pressurized by one legal compressor), then installed on the field to comply with transport dimension rules?

I envision a propane-tank-sized accumulator fit to the side of the bot, pressurized off the bot and closed with a valve, then attached to the pressure loop on the bot during the 1-minute field prep.

Quote:

R70 “Stored” air pressure on the ROBOT must be no greater than 120 psi. No stored air pressure intended for the ROBOT may be located off-board the ROBOT.
So no

BryceKarlins 06-01-2015 18:03

Re: Pneumatic Tank Restrictions
 
Quote:

Originally Posted by seg9585 (Post 1423059)
Here's a thought: could the tanks be pressurized while physically detached from the robot (still pressurized by one legal compressor), then installed on the field to comply with transport dimension rules?

I envision a propane-tank-sized accumulator fit to the side of the bot, pressurized off the bot and closed with a valve, then attached to the pressure loop on the bot during the 1-minute field prep.

Also, the tank is a part of the robot, therefore has to be included in the transportation configuration.

seg9585 06-01-2015 18:23

Re: Pneumatic Tank Restrictions
 
Quote:

Originally Posted by BryceKarlins (Post 1423096)
Also, the tank is a part of the robot, therefore has to be included in the configuration.

Well it has to be included within the transport configuration dimensions of the robot (28x42x78) ie physically placed inside that perimeter until the tank can be relocated elsewhere when placed on the field. For example, couldn't the tank sit within an area intended for tote intake/processing during transport, then moved to an external area when placed on the field?
Seems to be this is still in the spirit of "On-board the robot" even if the air isn't physically connected to the regulator/valve inlets until it gets on the field.

Kevin Sevcik 06-01-2015 18:26

Re: Pneumatic Tank Restrictions
 
Lets just back up for a second here. Why do you want to use one of these viair tanks anyways? The 0.5 and 1.0 gallon tanks are both about 2 lbs heavier than an equivalent storage volume of these clippard tanks. Are you that tight on space that you'd rather add the 2 lbs?

BryceKarlins 06-01-2015 19:16

Re: Pneumatic Tank Restrictions
 
Quote:

Originally Posted by seg9585 (Post 1423114)
Well it has to be included within the transport configuration dimensions of the robot (28x42x78) ie physically placed inside that perimeter until the tank can be relocated elsewhere when placed on the field. For example, couldn't the tank sit within an area intended for tote intake/processing during transport, then moved to an external area when placed on the field?
Seems to be this is still in the spirit of "On-board the robot" even if the air isn't physically connected to the regulator/valve inlets until it gets on the field.


Umm, I would say that kind of stretches the meaning of "on-board storage." I would ask at the Q&A to be sure, but a simple fix would be to just keep the tank hooked up to the system at all times, and simply move it outside the robot while keeping the hoses connected.

KMeyers 06-01-2015 19:23

Re: Pneumatic Tank Restrictions
 
Quote:

Originally Posted by Chris_Ely (Post 1422657)
One thing to keep in mind is that the typical compressors used in FRC only have a 9% duty cycle. They get very hot with prolonged use, such as filling a large tank. I would suggest mounting one of the large fans from the KOP next to the compressor to help cool it.

You could help reduce the load on the compressor by preloading the tank from an off-board compressor prior to the match.

Jon Stratis 06-01-2015 19:29

Re: Pneumatic Tank Restrictions
 
Quote:

Originally Posted by KMeyers (Post 1423171)
You could help reduce the load on the compressor by preloading the tank from an off-board compressor prior to the match.

Please see:
Quote:

R68 Compressed air on the ROBOT must be provided by one and only one compressor. Compressor specifications may not
exceed nominal 12VDC, 1.05 cfm flow rate.
Using an off-board compressor while having an onboard one is not legal.

Mr V 06-01-2015 19:39

Re: Pneumatic Tank Restrictions
 
Quote:

Originally Posted by Kevin Sevcik (Post 1423121)
Lets just back up for a second here. Why do you want to use one of these viair tanks anyways? The 0.5 and 1.0 gallon tanks are both about 2 lbs heavier than an equivalent storage volume of these clippard tanks. Are you that tight on space that you'd rather add the 2 lbs?


With this year's game I could see using the heavier tank purely because it is heavier since properly placed ballast can be something very useful this season.


All times are GMT -5. The time now is 05:36.

Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi