How to use an old cRIO with a 2015 driver station
 

What's a detailed procedure for doing the above, if possible.

Re: How to use an old cRIO with a 2015 driver station
 

My understanding is you can't.

Re: How to use an old cRIO with a 2015 driver station
 

Hmm, I swear I saw a post saying you could communicate with one http://www.chiefdelphi.com/forums/sh...97&postcount=2

Re: How to use an old cRIO with a 2015 driver station
 

Its seems to support the old protocol (via a switch on the setup tab), but when we tried to use it on our old robot, it would not connect. Its seems kind of wierd to include that option but not have it work.

Re: How to use an old cRIO with a 2015 driver station
 

That option on the DS was repurposed towards the end of beta testing and it no longer is used to connect to pre-2015 cRIO images using the '09-'14 communications protocol.

It now is used only to connect to the older FMS Lite which is only necessary if you will be using FMS Lite at home or will be attending a pre-ship scrimmage where FMS Lite is used instead of a regulation FMS.

Re: How to use an old cRIO with a 2015 driver station
 

From http://wpilib.screenstepslive.com/s/...ation-software

Re: How to use an old cRIO with a 2015 driver station
 

First you need to use the cRIO imaging tool and program it with the v57 image for cRIO. This image only supports the 4-slot cRIO.

After imaging, you can use LabVIEW for FRC 2015 (LabVIEW 2014) to target the cRIO-FRC II. You can connect to it using the latest driver station since this new image supports the new network communication protocol.

Re: How to use an old cRIO with a 2015 driver station
 

Thanks Joe,
I was on the verge of pulling out my last few hairs trying to figure out why the 2015 DS wouldn't connect to the last year's robot.
Question: Once we re-image the cRIO will it no longer work with the old DS?
I'd hate to lose the ability to backtrack to the old DS if something goes wrong.

Re: How to use an old cRIO with a 2015 driver station
 

It should still work with the old DS.

Re: How to use an old cRIO with a 2015 driver station
 

Is there any solution for an 8-slot cRIO, or would it be best just to buy a new roboRIO (a difficult thing for our small team)?

When I try to have both LabVIEW 2013 and 2014 installed, the old drive station will run just fine, but I wanted to make a new project in LV 2013 (just for a base drivetrain and joysticks since we tore our old bot down to be a drive practice bot) and I got a yellow triangle next to the cRIO part and it said something along the lines of "The plugin is either not installed or not activated for your system. Please contact National Instruments." Is this due to trying to run both? I ran the installer a second time in the same directory and there were no issues (it just flew through since there was nothing to do) and the NI License Manager doesn't show any issues.

Re: How to use an old cRIO with a 2015 driver station
 

When using the cRIO imaging tool found here: C:\Program Files\National Instruments\LabVIEW 2014\project\CRIO Tool
I only see an option for v52, which our cRIO already has... How do I get v57?

Re: How to use an old cRIO with a 2015 driver station
 

Did you install the LabVIEW update? Are you a LabVIEW team?

Re: How to use an old cRIO with a 2015 driver station
 

No, we're a Java team. I installed the National Instruments FRC 2015 Update Suite though.

Re: How to use an old cRIO with a 2015 driver station
 

Only LabVIEW has a v57 image. If you image the target as LabVIEW, you will see the option for v57, and you could then switch it back to Java.

However, this won't help you at all since Java doesn't support the cRIO this year. If you want to program in Java on the cRIO you have to use Net Beans and the libraries from last year.

Re: How to use an old cRIO with a 2015 driver station
 

Which means we'll have to use the old Driver Station?