Chief Delphi

Chief Delphi (http://www.chiefdelphi.com/forums/index.php)
-   Extra Discussion (http://www.chiefdelphi.com/forums/forumdisplay.php?f=68)
-   -   pic: 3081 RoboEagles KR-15905 Electronics Unit (http://www.chiefdelphi.com/forums/showthread.php?t=133813)

MrRoboSteve 31-01-2015 22:54

pic: 3081 RoboEagles KR-15905 Electronics Unit
 

xXhunter47Xx 31-01-2015 22:55

Re: pic: 3081 RoboEagles KR-15905 Electronics Unit
 
I'm interested on the wire management on this. It also looks like it's hinged but the way the jaguar is mounted it doesn't look like it closes.

Zebra_Fact_Man 31-01-2015 23:01

Re: pic: 3081 RoboEagles KR-15905 Electronics Unit
 
Curious how ventilation is going to work. Them electronics need to breathe!

orangemoore 31-01-2015 23:37

Re: pic: 3081 RoboEagles KR-15905 Electronics Unit
 
Quote:

Originally Posted by Zebra_Fact_Man (Post 1436816)
Curious how ventilation is going to work. Them electronics need to breathe!

It looks like it might be a nightmare to trouble shoot

Tungrus 01-02-2015 11:41

Re: pic: 3081 RoboEagles KR-15905 Electronics Unit
 
Trouble shoot may be a bit difficult but not a nightmare.

Hope the main circuit breaker is easily accessible. If I had to do this, I would make it in polycarbonate (lexan etc) to prevent electrical noise around roboRIO (I am not a expert but would cautious).

PAR_WIG1350 01-02-2015 14:57

Re: pic: 3081 RoboEagles KR-15905 Electronics Unit
 
Quote:

Originally Posted by xXhunter47Xx (Post 1436813)
It also looks like it's hinged but the way the jaguar is mounted it doesn't look like it closes.

It appears that the pivot is placed a bit above the top of the jaguar on the near half and above the level of the PDP breakers on the other half. There should be clearance, but I can't easily tell how much there will be.

MrRoboSteve 01-02-2015 21:55

Re: pic: 3081 RoboEagles KR-15905 Electronics Unit
 
Our goal with this design was:

1. Allow for electronics build off of robot
2. Electronics components either covered, mounted upside down, or mounted vertically
3. Easy to reach connectors on PDB from the side
4. Conserve space

It's made with 0.050 6061-T6 aluminum sheet. The top and bottom tabs on each side are fastened together with #8 screws. During the build, we install just the bottom screws, and can lay it almost completely open on the workbench. On the robot it can open about 30 degrees -- wide enough to get in to swap speed controllers and change wiring. If we need to open it further, the battery box next to it is fastened with 4 screws and is easily removed. The PDB and breaker are screwed to the box -- everything else is attached with Velcro

Here's a view of it from the side -- plenty of room for the Jag in there.

http://1drv.ms/169nz02

During the build, we did switch to use Talons inside there for five of our motors, as the layout worked better. We also moved the PDB up slightly to avoid interfering with the machine screws that attach it to the chassis. Because of that, we moved the circuit breaker to the outside of the box, "behind" the PDB.

I'm not super concerned about heat buildup. The unit is built like a chimney with an open top, bottom. The sides each have 16 square inches of opening for air to flow in. It's made out of aluminum, which is great at dissipating heat.

Here's an as-built photo. It shows the wire management.

https://twitter.com/MrRoboSteve/stat...62383760760832


All times are GMT -5. The time now is 14:42.

Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi