Chief Delphi

Chief Delphi (http://www.chiefdelphi.com/forums/index.php)
-   Extra Discussion (http://www.chiefdelphi.com/forums/forumdisplay.php?f=68)
-   -   pic: Team230 Damaged Frame Rail (http://www.chiefdelphi.com/forums/showthread.php?t=146519)

Billfred 09-10-2016 12:58

Re: pic: Team230 Damaged Frame Rail
 
Quote:

Originally Posted by chrisfl (Post 1611072)
Thank you all for the insights. Our team has been looking into trying a west coast drive this fall and this really helps. What other tips or tricks do you guys have in regards to west coast drive?

Whether 4901's design really is or isn't WCD is a fair question (we supported both ends of the shaft out of concern for the game), but we were running chain-in-tube as many WCDs do.

1) When dead-spacing chain, the term "designing an even number of links" means "2, 4, 6, 8" not "integer". Use a calculator; we like this one.
2) If you must run half-links because you ignored #1 or had a very good reason, make it the kind that don't have the little retaining pin you bend. That pin will be busted off by the other chain, and you will throw it, and you will be fishing new chain into your tube. (McMaster-Carr sells the good stuff.)
3) Dark Soul tool is so much better for making complete chain loops than any master link. Even the normal master link will, invariably, be busted off and you will throw a chain.
4) Design your drivetrain so you can get the main rail off without too much fuss. Riveting your belly pan every inch or so is too much fuss. (This was our greatest issue once we sorted out the chain; haven't designed a better plan yet.)
5) Drive your drivetrain early and often, to make sure your teething problems happen at home and not at your event. (You should be doing this anyway, but especially when you're doing a new-to-you drive system.)

Cothron Theiss 09-10-2016 17:07

Re: pic: Team230 Damaged Frame Rail
 
Quote:

Originally Posted by Billfred (Post 1611074)
4) Design your drivetrain so you can get the main rail off without too much fuss. Riveting your belly pan every inch or so is too much fuss. (This was our greatest issue once we sorted out the chain; haven't designed a better plan yet.)

Do you have any preliminary thoughts on how to design a belly pan such that the main rails can be taken off easily? I think that's a tough balance to find, considering that a belly pan has to be mounted properly to impart torsional strength to the chassis. Do you know of any teams that have worked this out?

BrendanB 09-10-2016 17:17

Re: pic: Team230 Damaged Frame Rail
 
Quote:

Originally Posted by Cothron Theiss (Post 1611103)
Do you have any preliminary thoughts on how to design a belly pan such that the main rails can be taken off easily? I think that's a tough balance to find, considering that a belly pan has to be mounted properly to impart torsional strength to the chassis. Do you know of any teams that have worked this out?

2590 Nemesis would be a great team to chime in on this. I know in 2014 and 2016 their rails were designed to be removable.

Cothron Theiss 09-10-2016 17:59

Re: pic: Team230 Damaged Frame Rail
 
Quote:

Originally Posted by BrendanB (Post 1611104)
2590 Nemesis would be a great team to chime in on this. I know in 2014 and 2016 their rails were designed to be removable.

Those are some gorgeous drivetrains. You can see a lot of thought when into many critical factors. The staggering of the rivets to not interfere with the runs of chain, the flexible coupling on the back axles for encoder mounting, and the way they've done the tabs in the belly pan are things I'll have to remember.

Thayer McCollum 10-10-2016 10:57

Re: pic: Team230 Damaged Frame Rail
 
https://drive.google.com/open?id=0B4...Q3RxV Wo2QTVJ

So I'm wondering if more teams do this? ^^ It's hard to tell from the picture but we welded thick wall aluminum tube (can't remember exact thickness) into the rail and then machined the weld flat and used a boring bar to achieve the diameter we wanted for the bearing. I feel like this would have prevented the damage to the rail in the original picture. What are your thoughts? Why don't other teams do this? Is it unnecessary? Do I just have no idea what I'm talking about? I am very curious.

Billfred 10-10-2016 11:17

Re: pic: Team230 Damaged Frame Rail
 
Quote:

Originally Posted by Thayer McCollum (Post 1611158)
https://drive.google.com/open?id=0B4...Q3RxV Wo2QTVJ

So I'm wondering if more teams do this? ^^ It's hard to tell from the picture but we welded thick wall aluminum tube (can't remember exact thickness) into the rail and then machined the weld flat and used a boring bar to achieve the diameter we wanted for the bearing. I feel like this would have prevented the damage to the rail in the original picture. What are your thoughts? Why don't other teams do this? Is it unnecessary? Do I just have no idea what I'm talking about? I am very curious.

I think it falls under "valid, but overkill for all but the most brutal of games". If wall thickness was a concern, doing something like 148 did with reinforcement plates at the bearings is probably a simpler method for most.

Chris is me 10-10-2016 11:49

Re: pic: Team230 Damaged Frame Rail
 
Quote:

Originally Posted by Thayer McCollum (Post 1611158)
https://drive.google.com/open?id=0B4...Q3RxV Wo2QTVJ

So I'm wondering if more teams do this? ^^ It's hard to tell from the picture but we welded thick wall aluminum tube (can't remember exact thickness) into the rail and then machined the weld flat and used a boring bar to achieve the diameter we wanted for the bearing. I feel like this would have prevented the damage to the rail in the original picture. What are your thoughts? Why don't other teams do this? Is it unnecessary? Do I just have no idea what I'm talking about? I am very curious.

Teams usually use 1/8" wall aluminum tubing for their drive rails, which prevents the problem. Some teams use bearing blocks or shims to provide even more material support to the bearing than the 1/8" wall tubing, which is safer. It's quite uncommon to use 1/16" wall tubing for drive rails at all, and I generally think it's not worth the weight savings to do so.

Your solution is essentially a welded-in bearing block, which seems overkill, especially compared to the various other bearing block solutions teams can come up with that aren't so tricky to machine and install. It'll work, but there are better uses of your time, and it'd be better to just not use 1/16" tubing for supporting bearings directly.

Thayer McCollum 10-10-2016 18:36

Re: pic: Team230 Damaged Frame Rail
 
So I suppose I should have clarified. I agree that structurally the tube concept is overkill. It adds support the rail doesn't really need. We did this because we felt that just pressing the bearings into the rail would cause them to fall out easily. Is that not the case? Does 1/8" wall easily support bearings without them falling out? Because in my experience that hasn't happened. If someone could tell me how to put the bearings in without them falling out I would be happy to learn. (Because those tubes really sucked to put in...)

Billfred 10-10-2016 19:45

Re: pic: Team230 Damaged Frame Rail
 
Quote:

Originally Posted by Thayer McCollum (Post 1611228)
So I suppose I should have clarified. I agree that structurally the tube concept is overkill. It adds support the rail doesn't really need. We did this because we felt that just pressing the bearings into the rail would cause them to fall out easily. Is that not the case? Does 1/8" wall easily support bearings without them falling out? Because in my experience that hasn't happened. If someone could tell me how to put the bearings in without them falling out I would be happy to learn. (Because those tubes really sucked to put in...)

For us:

1) Machine the hole just slightly undersized. Adjust it lightly when it's necessary.
2) Minimize axial slop on your axles. If your wheels can't slide back and forth on the axle, it makes it harder for it to wiggle the bearings too. (E-clips help with this.)

Joe Finkel 10-10-2016 22:45

Re: pic: Team230 Damaged Frame Rail
 
Quote:

Originally Posted by Thayer McCollum (Post 1611228)
So I suppose I should have clarified. I agree that structurally the tube concept is overkill. It adds support the rail doesn't really need. We did this because we felt that just pressing the bearings into the rail would cause them to fall out easily. Is that not the case? Does 1/8" wall easily support bearings without them falling out? Because in my experience that hasn't happened. If someone could tell me how to put the bearings in without them falling out I would be happy to learn. (Because those tubes really sucked to put in...)

1. RIM THE HOLE.
2. E-CLIP
3. RETAINING RING
4. SCREW AND A WASHER AT THE END OF THE AXLE

Chris is me 10-10-2016 23:04

Re: pic: Team230 Damaged Frame Rail
 
Quote:

Originally Posted by Thayer McCollum (Post 1611228)
So I suppose I should have clarified. I agree that structurally the tube concept is overkill. It adds support the rail doesn't really need. We did this because we felt that just pressing the bearings into the rail would cause them to fall out easily. Is that not the case? Does 1/8" wall easily support bearings without them falling out? Because in my experience that hasn't happened. If someone could tell me how to put the bearings in without them falling out I would be happy to learn. (Because those tubes really sucked to put in...)

Bearing retention really has very little to do with the wall thickness of the material the bearing is pressed in. How the hole is sized is the biggest factor, really. Machine the hole a thou or two undersize for a nice press fit, but not so much under the bearing will seize. If you can't do this, using green loctite (gap filling) will help hold the bearing press fit in securely. Otherwise, you can use the hardware on your shaft to hold your bearings in (spacers, etc).

I would definitely not recommend an E-clip to do this if the E-clip is between loads, only on the end. And even then a snap ring is simply the better tool for the job.

Fusion_Clint 10-10-2016 23:05

Re: pic: Team230 Damaged Frame Rail
 
Quote:

Originally Posted by MamaSpoldi (Post 1565869)

Why are the holes offset from each other? It appears that the inner hole is at least 0.125" further to the left as pictured that the outer hole showing the damage.

Chris is me 11-10-2016 09:25

Re: pic: Team230 Damaged Frame Rail
 
Quote:

Originally Posted by Fusion_Clint (Post 1611255)
Why are the holes offset from each other? It appears that the inner hole is at least 0.125" further to the left as pictured that the outer hole showing the damage.

I'm fairly sure that's just the camera angle here; their drivetrain was a fairly normal WCD.

(haha, get it, "normal", I crack myself up)

MamaSpoldi 13-10-2016 10:33

Re: pic: Team230 Damaged Frame Rail
 
Quote:

Originally Posted by Billfred (Post 1611038)
I can't speak for 230, but 4901 never replaced any of their 1/8" wall tubing through two competitions and demos. The final exam would be next weekend at SCRIW.

After the rest of a long season... and off-season events... and community events, I can report that the replaced tubing has held up great.


All times are GMT -5. The time now is 23:13.

Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi