![]() |
2004 Kit Changes Wish List
Hey everyone,
First of all, I'd like to try not to turn this into a drill motor debate thread. So, other than that, what changes would you hope to see to the 2004 kit (within reason - no anti-gravity devices will make their way into the kit). Personally, here's what I'd like to see: -Slightly different batteries with totally square terminals so larger hardware can be used without deforming the terminals. -Return of the seat motors -Different window motors (maybe like the older ones) The new ones had way too much slop. |
More 0.75" ID Phlanged bearings Thos things are like $9.95 each!
|
I definately want to see the return to the drill/clutch housing.....
-Pat |
Kit wishes...
I've said it before... half the motors and twice the pneumatics!
Mr. Van |
The models and quantities of motors in the kit are largely dependent upon the motors that are donated to FIRST by companies like Bosch, Fisher Price, Delphi, etc. Any “request” we make of FIRST to change the quantity or model of motors provided in the kit will probably not be acted upon (unless you’re lucky and one of those companies has a few thousand extra of a particular model) because FIRST is at the mercy of these companies.
I hope that rules regarding pneumatics are opened up this year. If we could 5+ cylinders <cough>multiposition</cough>, while being given roughly the same number of motors (2 drill-ish, 2 CIM-ish, 2 FP-ish, 2 Globe-ish, 2 Window-ish, 1-2 Van Door-ish, and maybe 1-2 Seat-ish), I’d be a very happy camper ;). I’d also like to see the scoring object fit into one of those kit containers again :P. I really liked the fact that FIRST had couplers and adapters made for the Window motor, the all new Drill assembly, and the CIM assembly. That was very useful, at least for prototyping. Keep up the baby steps FIRST! Quote:
I’m sure that it isn’t just a characteristic of west coast teams not to use those large bearings on your robot. If you asked around I’m sure you’d find lots of teams who would be willing to trade you theirs for something of yours. Teams out here have entire bins full of those huge bearings. |
Quote:
I really did enjoy all of the custom FIRST-specific new kit parts last year. |
The answer to this is extremely easy. Let FIRST add 3 rolls of classic Duct Tape to the kit. No robot will have any problems. If they do, "Fix it in code".
In all honesty, I would like to see a few pulleys in the kit. Our team had a fun time getting them last season. Oh, and a spare "golden" nut for the 120A breaker wouldn't be bad either. I lost one of the nuts last season, and spent far too much time searching on the floor for it. ______________________ "Arms broken? We'll fix it in code." |
To add to that it'd be nice if they provided a list to what size hardware or threaded holes was used in every applicable component of the kit so we wouldn't have to guess.
|
Quote:
|
I think that FIRST's little baby steps with the motor mounts and everything is just fine and they should keep that up. However i have been saying since i became addicted to FIRST that more pneumatic freedom would be great. It would really open up the doors for some spectacular engineering. So thats all i want to see changed more pneumatic freedom.
|
mabie they will losted up the rules on the compressor because we wont be getting one this year
|
More pneumatic freedom.
I remember an old post about a team that unknowingly cheated (had they read the rules right, they probably wouldn't have done it). They used box aluminum as their frame and made it air-tight. Then they hooked up their air lines into the box-alum frame, thus creating a much larger volume of ready-to-use air than just using the kit tanks. I think if I team can do something like this, they should be allowed to. But still it must pass a no-leak safety inspection and follow all other guidelines given. Pneumatics is a great thing for robotics, especially for the type we do. A lot of great designs have involved pneumatics, and only greater ones can come from more freedom in designing. If we aren't allowed to think outside the box, give us a bigger box. |
Quote:
We'll say that whatever they give us isn't enough, but in the end, it will be. |
Quote:
Remember, half the fun of FIRST comes from trying to think of what box to think outside of ;) |
I'm sorry i havent been to CD for a while now.....who and where was it said that there would be no compressor?
|
| All times are GMT -5. The time now is 17:54. |
Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi