Emergency! Need Help With Ir Sensors
 

Hi! guys I only have 7 more days and I am not even done with my IR sensors.
* The problem I am having is Using navigate.c whenever i put navigate.c in my robot it doesn't work unless i connect the motors to PWM 3&4 and. Once I am done connecting the motors to PWM 3&4 the robot goes crazy it just goes everywhere and it doesn't move it's servon motors and doesn't detect beacon.

* When I put my Motors on PWM 13 & 15 the robot doesn't move at all it doesn't perform any movement all it does is just straightens up the sensors and that's it. The programm gives the command "MOVE TO CENTRE" but it doesn't perform the action.

* Does anyone know why I am having this troubles please help me? I am pretty much furustrated and if you want to contact me my msn is jigarjuhi@yahoo.ca and that's my e-mail so it's 2 in 1. Please help me! :ahh: :confused: :(

Re: Emergency! Need Help With Ir Sensors
 

Ok, here goes,
What pwm's are you plugging the servos into?
Made sure that the cable orientation is correct the IR's, servos, motors, PWMs?
I'm loading up the navigate code right now!!

Re: Emergency! Need Help With Ir Sensors
 

of course it doesn't move when you plug the motors into pwms 13 and 15 - navigate doesn't output to those pwms.

if it's moving crazily when you plug them in to pwms 03 and 04 (the correct ones), then you probably need to adjust the values in the program to suit your sensors, as well as make sure the servos are hooked up correctly.

Re: Emergency! Need Help With Ir Sensors
 

I am currently using PWM 1 and PWm 2 for servo motors
I use the IR's in Digital I/O 1,2,3,4 and motors into PWM 13 and 15.

Re: Emergency! Need Help With Ir Sensors
 

As delta pointed out, 3 and 4 are the correct ones (how did you come up with 13 and 15?). I would just recomend leaving them unplugged or blocking up the robot to see how it acts through the debug port.

Re: Emergency! Need Help With Ir Sensors
 

I believe the IR sensors belong on digital 1&2 and digital 4&5.
Verify by looking at the comments in the header of the receiver.c file.

The motors go on pwm3 & 4
The servos go on pwm1 & 2
Verify by looking at the code in navigate.h

Re: Emergency! Need Help With Ir Sensors
 

Are you utilizing PWM 13 and PWM 15 because you are using a tank drive system?

Re: Emergency! Need Help With Ir Sensors
 

13 and 15 would probably come from the code for single-joystick navigation in the default program.

Re: Emergency! Need Help With Ir Sensors
 

for some reason after connection the motors to pwm 3 and 4 the robot just goes crazy it just sought of goes everywhere bashing everything. Anyone knows why?

Re: Emergency! Need Help With Ir Sensors
 

are your motor polarities correct? if one were backwards, the robot would turn when it thinks it's going forward, and go forward or back when it thinks it's turning... this would cause some really strange behavior.

Re: Emergency! Need Help With Ir Sensors
 

I'd put it up on blocks and check the status of the IR sensor tracking.
Call the tracker alone without the navigate and print out the tracker status:
Tracker_Data[left].Status, Tracker_Data[right].Status

Also observe how the servos behave.
Does it hold on the beacon or look all over the room?

After you're sure the tracker/beacon combo are working correctly, then move on to debugging the navigator code.

Re: Emergency! Need Help With Ir Sensors
 

Hey,
is there a way to see if the IR / optical sensors work, i mena for the beacon you just get a camera, what is the way to c if the IR sensors are working. And whts the shipping time, if any of you have ordered new IR sensors..

Re: Emergency! Need Help With Ir Sensors
 

There are several easy methods.

- You can just check the IR receiver buffers, see Kevin's FAQ or other posts for what to look at and how to interpret the data.

- You can disconnect the servos and printf the Tracker_Data[left].Status & Tracker_Data[right].Status, i.e., the tracker states are:
NONE_IN_VIEW 0
RIGHT_IN_VIEW 1
LEFT_IN_VIEW 2
BOTH_IN_VIEW 3

- Using a regular digital input printf the value of the sensor. In the presence of the beacon or a compatable IR source like a TV remote you will see a mixture of 1's & 0's. Bad sensors show all 1's or all 0's.

For shipping you can order overnight of course. 1st class TX to NY was a couple of days (Friday to Tuesday over a holiday).

Re: Emergency! Need Help With Ir Sensors
 

We also had similar problems with our robot going crazy with the tracking code...but then we realized our IR sensors weren't plugged in. But FYI, i think servos are supposed to plug in to PWMs 3 and 4. Your robot was going crazy because the pwm values were switching back and forth because the program thought they were servos and was sweeping the field with them... :rolleyes:

Re: Emergency! Need Help With Ir Sensors
 

i had tht hunch dont know if it is true, but can you please point out where the motors will go than..i mean drive motors