pic: Team Rush 27 - Shooter Concept
 

Re: pic: Team Rush 27 - Shooter Concept
 

Ooh.. So pretty.

Is this a stationary attachment, or is it turning, and if so how many times?
If so, where are the wires headed?

Great CAD so far. Hope to see it soon.

Re: pic: Team Rush 27 - Shooter Concept
 

Its seems to be made to turn. You can see a globe motor mounted upside down to the left. I think they were just to lazy to actually make the sprocket and at the moment there is just a solid ring.

Re: pic: Team Rush 27 - Shooter Concept
 

pictures of the turret have already surfaced.......so yes it spins.

it spins as much as we want it to, though i doubt it would ever travel more than 180 degrees. this turret is for precision movement....it mimicks the camera gimble.

as for wires, i can't say. we've managed to build a turret for the last 5 years....wires have never been a "go," "no go," item.......they will most likely run around the back of the device and be placed inside some slick looking wire loom. leave plenty of slack...and bam!, your wired. :D

i'll let the electric knobs work on that. ;)

not too lazy......

there is no sprocket involved. see either picture already posted. it is a 129 tooth, 12DP, 20 degree PA spur gear.

that is hard to draw! not to mention frivolous. keep in mind the title of the pic..."concept." this implies that you aren't seeing a completed drawing.

Re: pic: Team Rush 27 - Shooter Concept
 

I've been curious to see what some other folks do to 'shield' their mechanisms as per the rules. Do you plan to cover the wheels more than what is shown or do you feel that the standoffs are adequate?

Re: pic: Team Rush 27 - Shooter Concept
 

i think the standoffs are adequate. it is a tough call though.....

as designed there is plenty of room to insert a finger and have it severely mangled. but there is enough room to keep from having the finger wedged. for now the standoffs stay.

there are also other mechanisms near or around the shooter.....these may ultimately provide enough protection from the shooter wheel.

Re: pic: Team Rush 27 - Shooter Concept
 

so, how do the balls go from your other pictures to be put within the wheels to shoot towards the goal? the force of pushing them upwards allows them to get sucked in with in your shooter and there it goes?

Re: pic: Team Rush 27 - Shooter Concept
 

Seems like it would be safer without the standoffs. I'm thinking the standoffs would help the wheel suck your fingers in, instead of keeping them out. Full shield or no shield is what I say.

Re: pic: Team Rush 27 - Shooter Concept
 

the balls simply transfer from the ball elevator, through the turret and into the shooter. you can't see from these pics, but the design allows for the lift rollers to get extremely close to the underside of the turret.......balls pop up through the bottom and fly away.

the design was executed in such a way that the location of the turret and the elevation of the gun don't change the loading location.

Re: pic: Team Rush 27 - Shooter Concept
 

I want me one of those!
...........or two :p

Re: pic: Team Rush 27 - Shooter Concept
 

I should have looked at this post first - answers my question from the picture in your other post. Looks sweet.

Craig

Re: pic: Team Rush 27 - Shooter Concept
 

Whoever designed that, has skill.

Re: pic: Team Rush 27 - Shooter Concept
 

meh. they downloaded stuff. slackers :D
but wow. detail. with we had the resources to pull sumthing like that off.
if you dont connect the pitching of the 2 sides, then you can control more aspects of the ball.
launch angle, direction are obviously doable, and by changing the rotation speeds of either side will change the spin sideways, and by haveing a different launch angle with right and left you'll have a sorta rifling rotatioin too. fun!!

Re: pic: Team Rush 27 - Shooter Concept
 

Using what software?
I can crank that out in about 10-15 minutes in SolidWorks.
But then again, I have been using it for at least 3-4 years now.

Re: pic: Team Rush 27 - Shooter Concept
 

Elgin,

I have a new found respect for you now that I know you use SolidWorks.

I have been using it since 1997 and the ThunderChickens have been using it since 2001.

Anthony,

Nice shooter. I'm not a big fan of the side by side, but you guys looked like you have a good design. BTW, I agree with Elgin, it is pretty easy to draw gears in SW, but it is definitely unnecessary.

-Paul