Chief Delphi

Chief Delphi (http://www.chiefdelphi.com/forums/index.php)
-   Programming (http://www.chiefdelphi.com/forums/forumdisplay.php?f=51)
-   -   How is your camera mounted? (http://www.chiefdelphi.com/forums/showthread.php?t=45102)

bear24rw 06-03-2006 18:15

How is your camera mounted?
 
Just interested in how other people have their cameras set up...

Eldarion 06-03-2006 18:22

Re: How is your camera mounted?
 
Mounted on the turret with a tilt servo; using turret to pan.

The tilt servo only has two positions, near and far. :)

Stuart 06-03-2006 18:29

Re: How is your camera mounted?
 
ours is mounted (poorly . . . one of the things well be fixing on our thursday) on our turret, with both the tilt and pan servos(the turret is only 320 deg so we left the pan servo on to "keep a beat on the light"

Rickertsen2 06-03-2006 19:05

Re: How is your camera mounted?
 
We used the pan/tilt assy in the kit but locked the pan axis in place. Tilt is controlled by our turret. There is a lexan wall protecting it

SoftwareBug2.0 06-03-2006 19:56

Re: How is your camera mounted?
 
Pans with turret, no vertical adjustment.

team222badbrad 06-03-2006 19:59

Re: How is your camera mounted?
 
Who needs a camera? We don't have one.

Donut 06-03-2006 20:35

Re: How is your camera mounted?
 
Camera on turret with both pan and tilt servos. We decided the rotator would not have enough angle of rotation to be an effective pan adjustment for the camera (our rotator only does 40-60 degrees, just enough to hopefully keep us pointing at the goal if we start getting pushed while shooting), plus the camera can search faster moving the pan servo rather than the rotator.

mogunus 07-03-2006 17:14

Re: How is your camera mounted?
 
Our cameras are mounted one on either side of the turret mechanisim, both on pan/tilt servos. The turret itself pans and tilts.

looks sorta like this:


[[O]]---()______()---[[O]]

With the () being the rotating shooter motors, and the little [[O]] things being the cameras mounted on the pan/tilt servos.

bear24rw 07-03-2006 17:26

Re: How is your camera mounted?
 
Quote:

Originally Posted by mogunus
Our cameras are mounted one on either side of the turret mechanisim, both on pan/tilt servos. The turret itself pans and tilts.

looks sorta like this:


[[O]]---()______()---[[O]]

With the () being the rotating shooter motors, and the little [[O]] things being the cameras mounted on the pan/tilt servos.

You have two cameras? How did you wire them through one port?

mogunus 07-03-2006 17:50

Re: How is your camera mounted?
 
Quote:

Originally Posted by bear24rw
You have two cameras? How did you wire them through one port?

I didn't. I have a custom circuit board with three rs232 level serial ports, two of which connect to the two cameras and one of which connects to the program port on the PIC, not the TTL level port.

Binocular vision could also be accomplished by connecting one camera to the program port and one to the TTL port, and then messing with Kevin's camera driver code to use the cameras on both ports. My way was just easier, 'cause I'm lazy.

Also note: the cameras don't really need to be powered by the 7.2 volt power supply on the PIC board. If you're not powering the servos off the camera board, 5v will do just fine in powering the camera itself, it says in the "Big Binder of the Camera" that power goes through a 5v regulator. So just hook up the camera to a digital inout or whatever for power, and you won't have to deal with backup battery foolishness, because that silly thing was being drained far too quickly by our two camera setup.

Caleb A. 08-03-2006 11:09

Re: How is your camera mounted?
 
Our is mounted completely reversed (y pan and backwards, x is tilt and backwards) because my crew didn't listen whenever the built the camera casing and it has to be out of the way of the shooter. The camera itself is mounted on our Shooter so the robot pans and the shooter tilts. Probably won't end up using it though depending on how much practice time I get.

eugenebrooks 11-03-2006 01:26

Re: How is your camera mounted?
 
Our camera is mounted in a piece of 2x2 aluminum box tube, that is bolted to the turret. The camera itself is epoxied to the board it is plugged in to, using two wood blocks, and the wires are soldered to the board so no connectors can work out due to vibration. The camera lens looks through a hole in the box tube.

The camera pans with the turret using feedback to keep the turret locked on the target. The height of the target is used to control the wheel speed so that a fixed 45 degree shooter can hit the target from different ranges.

sur2124 14-03-2006 20:08

Re: How is your camera mounted?
 
ours was mounted underneath the turret to prevent any from ball hitting it.

chrisinmd 14-03-2006 20:30

Re: How is your camera mounted?
 
Ours is mounted directly in front of our shooter wheel, with lexan protection of course, and the balls go over it. We just used the top part of the pan/tilt assembly, with only the tilt servo being used.

ewankoff 15-03-2006 11:19

Re: How is your camera mounted?
 
ours is on the turret and usses servos


All times are GMT -5. The time now is 03:37.

Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi