HELP: analog input
 

Hey,
I'm trying to get an analog input from my 10 Kohm but all i get is a series of numbers counting downwards and reseting the controller makes it go back from the number in which it stopped instead of the one in which it began...

Any suggestions?

Re: HELP: analog input
 

If you could post the relevant portion of your source code here, we could offer you some insight.

Otherwise, the best we could offer up is a generic "look at Kevin's code" here: http://www.kevin.org/frc/ response.

Re: HELP: analog input
 

printf("Pot %d\r", Get_ADC_Result(1));

Re: HELP: analog input
 

The counting occurs when nothing is connected.
Make sure that the Pot is plugged into the right pin.
In Kevin's ADC, #1 is actually analog in #2 (#0 is pin #1).

Re: HELP: analog input
 

we did what you said but it still counts.
can any body please send us a working code for the potentiometer using the analog inputs.

Re: HELP: analog input
 

Without using Kevin's code:

Potentiometervalue = Get_Analog_Value(rc_ana_in01);

Re: HELP: analog input
 

I think Bharat is trying to tell you (and he's right) that it's overkill to use my code to read a potentiometer. Just use his example and it should work. If you really want to use my code, if I remember correctly, Get_ADC_Result() returns an unsigned int, which means you should use %u in your printf() format string, not %d.

-Kevin

Re: HELP: analog input
 

We have tried both things, with Kevin's code and it still did not work...
any further suggestions?

Re: HELP: analog input
 

Is your potentiometer wired correctly? Red and black to the outer leads, white (signal) to the center? The problem you described only occurs when nothing is plugged in, so make sure you're referencing the correct analog input in your code, that the pot is wired correctly, and that it's not broken (which is kind of hard to do.. test another one?).

Re: HELP: analog input
 

We tested it with a voltmeter and it all good....

Re: HELP: analog input
 

But is it wired up correctly? You can test it at a point on the potentiometer and get correct readings. However, if it is not wired up correctly, the processor will not be able to read it. There is also a slight chance the processor itself has corrupted analog pins. That happen to our 2006 controller at the end of the season.

Re: HELP: analog input
 

the potentiometers are good like i said...
We have checked it with a voltmeter connecting between the where the white cable connects and where the red one connects and it shows the correct results.
We have also tried to change the ports, and neither of them worked...

Re: HELP: analog input
 

If your idea of "good" does not match what the RC expects, it won't work no matter how many times you check to see that it's "good". In order to help you, we need to know exactly how you have wired it. Answering "we wired it correctly" is not going to help. For example:
But where did you connect the black wire? What measurement are you making, and what results are you getting? Answering "the correct results" does not help.

A potentiometer on the Robot Controller's analog inputs needs three wires. Black (ground) goes to one end of the pot. Red (+5) goes to the other end of the pot. White (signal) goes to the wiper.

Re: HELP: analog input
 

Like i said before...its connected CORRECTLY...
There is another problem...
Black goes to left side of potentiometer
Red goes to its right leg
and white goes to the middle one...
and they connect to the analog inputs correctly
We have measured voltages between red and white legs, and it shows inputs from 0 to 4.95V liniarically to the rotation i make...

Here's our code:
printf("%u",Get_Analog_Value(rc_ana_in01));

does not work with %d or %u....

could you show me the code of Get_Analog_value...perhaps the problem we have has to with that function...

Re: HELP: analog input
 

I don't know this first hand, but does the analog port need to be setup as an input somewhere? Does the ADC need to be enabled?

ttyl,

--buddy