Chief Delphi

Chief Delphi (http://www.chiefdelphi.com/forums/index.php)
-   Robot Showcase (http://www.chiefdelphi.com/forums/forumdisplay.php?f=58)
-   -   sneak peak (http://www.chiefdelphi.com/forums/showthread.php?t=68701)

c9ollie 04-08-2008 03:04

sneak peak
 
super rough draft

looky looky










Al Skierkiewicz 04-08-2008 08:01

Re: sneak peak
 
Very nice! Don't forget to add some cross bracing to the vertical members. And always remember that rubber tread moving next to the motor will induce some static electricity.

AdamHeard 04-08-2008 09:01

Re: sneak peak
 
How thick are those sideplates? I am almost they are currently not thick enough to be strong enough

vivek16 04-08-2008 09:14

Re: sneak peak
 
Ditto. They look 1/32 to 1/16ish. Make em thicker. I'm not sure how thick but 1/4" is probably a safe bet.

-Vivek

c9ollie 04-08-2008 14:40

Re: sneak peak
 
Quote:

Ditto. They look 1/32 to 1/16ish. Make em thicker. I'm not sure how thick but 1/4" is probably a safe bet.

-Vivek
they are a 1/10 anything more is shear over kill and more weight. we ran 1/10th side panels last year with zero issues. the illustration rendering style has a black outline on every edge so it makes them look super thin. this is just a revamp of our current transmissions so we know they are already tough as nails. also the wheel does not rub on the motor its just packaged in a way that it looks like it does. i will get a few more renderings to show it. the top ring is just our packaging goal. also pictured in these renderings is the lower support bearing. i didnt have time to model it in the first renderings.

btw this is for our crab drivetrain.




Dowjonesbotics 04-08-2008 15:29

Re: sneak peak
 
Is this what they call a swerve drive????:confused: But hten what's a crab drive???

I'm a little confused as to the difference

DarkFlame145 04-08-2008 15:31

Re: sneak peak
 
your not already planning on using a crab drive for the 09 year, are you?

EricH 04-08-2008 16:40

Re: sneak peak
 
Quote:

Originally Posted by Dowjonesbotics (Post 760097)
Is this what they call a swerve drive????:confused: But hten what's a crab drive???

I'm a little confused as to the difference

It isn't exactly in the modules. You could have both of those with the same modules and different turning gearing.

It's the way it's set up. Correct me if I'm wrong, but a swerve drive has two or more sets of modules and a crab drive only has one. (Or it's the other way around.)

I'm going to say that 1/10 is too thin for stress points. What a lot of teams do is take 1/4 and put the holes in, then mill the rest of the plate out, leaving a border and a small area around each hole at original thickness to add strength. You really don't want to make a mistake and go too thin; having the thin stuff fail mid-match will take your robot out of the match. No spare means you may be out of the competition.

If nothing else, do the stress analysis and post it so that we know that you know what you are doing. If that analysis (which should probably take into account getting hit by 3 robots simultaneously from the same side) shows that it won't break, even under running conditions, then I'll retract my statement that 1/10 is too thin. If it doesn't, then we'll help you redesign so that it won't fail.

=Martin=Taylor= 04-08-2008 18:54

Re: sneak peak
 
I'm not as concerned about the thin-ness as I am about the lack of connections between the two sides. You really ought to add some standoffs down near the wheel, or better yet, machine the whole module out of .125" thick boxed aluminum.

You could always use steel. That would certainly strengthen the connection points.

Daniel courtney 04-08-2008 23:40

Re: sneak peak
 
Quote:

Originally Posted by c9ollie (Post 760094)
they are a 1/10 anything more is shear over kill and more weight. we ran 1/10th side panels last year with zero issues. the illustration rendering style has a black outline on every edge so it makes them look super thin. this is just a revamp of our current transmissions so we know they are already tough as nails. also the wheel does not rub on the motor its just packaged in a way that it looks like it does. i will get a few more renderings to show it. the top ring is just our packaging goal. also pictured in these renderings is the lower support bearing. i didnt have time to model it in the first renderings.

btw this is for our crab drivetrain.




lol that looks like a disc brake in the wheel...or is it?

vivek16 05-08-2008 01:39

Re: sneak peak
 
Quote:

Originally Posted by Daniel courtney (Post 760171)
lol that looks like a disc brake in the wheel...or is it?

I think its a gear.

-Vivek

AdamHeard 05-08-2008 01:59

Re: sneak peak
 
Quote:

Originally Posted by Hachiban VIII (Post 760135)
I'm not as concerned about the thin-ness as I am about the lack of connections between the two sides. You really ought to add some standoffs down near the wheel, or better yet, machine the whole module out of .125" thick boxed aluminum.

You could always use steel. That would certainly strengthen the connection points.

Yes, with the .1 thickness, some real serious cross support will need to be added for it to be strong enough. More than just some cross supports probably.

Imagine the stresses the module can take when it rapidly changes directions while the robot is moving full speed (and even worse takes a hit from another robot at the same time).

Al Skierkiewicz 05-08-2008 07:29

Re: sneak peak
 
Quote:

Originally Posted by Dowjonesbotics (Post 760097)
Is this what they call a swerve drive????:confused: But hten what's a crab drive???

I'm a little confused as to the difference

Swerve drive and crab are very similar and often the two terms are interchanged. Many years ago, some teams developed a type of drive that could steer all four wheels but had limited turning of the running gear. It allowed the robot to "swerve" around obstructions on the field. Crab drive allows the robot to move in any direction without needing to turn the robot. The steering gear has the ability in most cases to turn more than 180 degrees and sometimes continuously. The first robot I remember with crab was a Chief Delphi robot from around '97 or '98 and there was one steering motor and a chain that wrapped around all four steering modules.

c9ollie 05-08-2008 12:57

Re: sneak peak
 
Quote:

Originally Posted by AdamHeard (Post 760184)
Yes, with the .1 thickness, some real serious cross support will need to be added for it to be strong enough. More than just some cross supports probably.

Imagine the stresses the module can take when it rapidly changes directions while the robot is moving full speed (and even worse takes a hit from another robot at the same time).

i can assure you that 1/10 is as thick as it needs to be anymore more is just a waste of time and pocketing 1/4 plate is just waste of aluminum. we ran this exact setup last year with zero issues. the frame of our robot bent before these "PODs" did. also since this is a super rough draft and i havnt really got to making the spacers for it. there is more support in these PODs but im more concerned about the geartrain layout.

Al Skierkiewicz 05-08-2008 13:07

Re: sneak peak
 
Quote:

Originally Posted by c9ollie (Post 760238)
i can assure you that 1/10 is as thick as it needs to be anymore more is just a waste of time and pocketing 1/4 plate is just waste of aluminum.

Ollie,
Don't forget that a 140lb robot running at 12 ft./sec imparts a pretty big side load to your module and all the force will be transmitted to the frame through the ring and a small amount to the top bearing. You can't keep your friction numbers unless all the tread is on the floor.


All times are GMT -5. The time now is 00:02.

Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi