2009 Distribution Block
 

Well, we've seen the new Jaguars, and the cRIO...

What about this new Power Distribution Block? If there's one thing we really need its a new distribution block... :)

Anyone know whos making it? Where it can be found? Is it already on the market?

Can I download a CAD yet? :D

Re: 2009 Distribution Block
 

http://www.chiefdelphi.com/media/photos/31404

the thing in the middle, from what I hear, is much like the IFI board from 2005, combining the functions of power distribution and holding the fuses.

Re: 2009 Distribution Block
 

Here is more info: http://first.wpi.edu/FRC/powerdistribution.html

Re: 2009 Distribution Block
 

From my understanding the new distribution block is being fabricated by Diversified Systems (DivSys) out of Indianapolis. These are the same folks who provided the IR boards last season.

Re: 2009 Distribution Block
 

hmmm, i guess we'll just have to hope that these boards work better than the IR ones (my team could never get them to work), though they do look very nice so far.

Re: 2009 Distribution Block
 

I have firm reason to believe these will be the best power distribution blocks since the 2005 season.

Re: 2009 Distribution Block
 

I totally get what you're saying, but that isn't saying much, given that IFI boards were great, and the distro blocks the last 2 years sucked.

Re: 2009 Distribution Block
 

Yeah, but didn't that one use push-on connectors?

This one uses screws to clamp down the leads... the same method the Rock-fail-well Distro' block used :mad: Those screws always came loose.

We shall see... At least its nice and compact and not too heavy-looking..

Re: 2009 Distribution Block
 

Nope.

The main battery leads are ring crimped and attached to a pair of press fit shanks. A nut is then tightened down on top of this. This is similar to the old IFI breaker board and the 120A main breaker connection, but with enhanced awesome. These are the square chunks of metal on the right hand side of http://first.wpi.edu/Images/CMS/Firs...ax_600x406.jpg

As for the fanout past the breakers, these use Wago 745-85X and 745-83X cage clamp style connectors. A piece of spring steel, not a screw, supplies the clamping force. These are the blue and white connectors on the top and bottom of http://first.wpi.edu/Images/CMS/Firs...ax_600x406.jpg

Re: 2009 Distribution Block
 

I like the New Control System, the 07-08 was really annoying.

Re: 2009 Distribution Block
 

Care to elaborate?

I for one enjoy using products that work--something IFI is very good at.

FIRST has a dismal track record when it comes to introducing new vendors/products into FRC. It's going to take a lot more than fancy specs to make the new controller superior to the old--first it has to work, which is no small task.

Re: 2009 Distribution Block
 

For one, on the distro block the terminals were very hard to work with. They would wiggle out. There were other small things that i do like about the new controller. The new distro block has everything included into a package. BTW, Cory what terminal connectors did you use one your batteries, they were really cool.

Re: 2009 Distribution Block
 

I think it's important to distinguish between IFI and third party manufacturers. IFI manufactured the control system. They are in no way responsible for the shortcomings of a product being used outside of it's intended application (the Rockwell Distribution Block)

As for our batteries, we just used standard ring terminals. We had 4 gauge monster wire, which was what looked different from most teams.

Re: 2009 Distribution Block
 

Oh, otherwise IFI products were great. Can you give me link to the standard ring terminals. Thanks Cory

Re: 2009 Distribution Block
 

Please note that the Rockwell block has a specification for strip length that teams chose to ignore. Without stripping to 5/8", the wire was guaranteed to push out as the screws were tightened. The new Waco blocks have a similar specification. You must strip 1/2" of insulation for the wire to be properly terminated in the 745-85X block according to the manufacturer. You must strip 1/3" of insulation for the wire to be properly terminated in the 745-38X block according to the manufacturer. Their ability to stand up to robot movement will be tested during the beta testing. Please standby...

We might as well get this discussion going early, so let everyone know what the spec is.