Re: pic: Andymark's New Product
 

Very Nice RC, now only if I could come up with something. Lol.

Re: pic: Andymark's New Product
 

Certainly cheaper than tensioners that you can get from McMaster-Carr... that's a huge bonus.

Re: pic: Andymark's New Product
 

We'll definitely be buying them. Only worry that comes to mind is if there's enough material to take the wear and tear without "wearing through"? The tensioners we made ourselves out of Delrin probably had a 1/2" of solid backing and I'll bet we wore through 1/8" of it. Looks like there might only be 1/8" there, but it's hard to tell w/o dimensions. Have you done any testing on wear?

Thanks,
John

Re: pic: Andymark's New Product
 

UHMW is a harder plastic than delrin. Our Mcmaster Carr ones only wore 3/16th's and we used them for almost 2 years.

Re: pic: Andymark's New Product
 

not in all cases. standard uhmw is around 66 shore D while Delrin is around 86 shore D

Since these are both plastics which can contain glass filling, other materials, recycled plastic it is not wise to make generalizations about materials. Especally in this case where you didn't state the exact material which these are molded and the exact type of delrin they used.


On another note, I am not sure that hardness is the correct measure for effective chain tensioners. I would think it has to do with the lubricity of the material and the ductility. While hardness probably comes into play (ie why gum rubber wouldn't be a good tensioner) It is not the only (or possibly the main one) which needs to be considered.

Re: pic: Andymark's New Product
 

I'd like to make a suggestion for this thread and the AndyMark website...

I have been following the development of this product since the first CAD drawings were posted on CD. Now, I think I'm a fairly smart guy... college educated and a pretty good software engineer.... it took me a very long time to realize these would be used as a pair and tie wrapped together. Now I realize why everyone thought the idea was so beautiful in its simplicity.

Now for the suggestion... could you show a picture of it used on a robot? I think that would help people (maybe I'm the only one) understand how to use it and why it's so effective.

Re: pic: Andymark's New Product
 

Ok. I can safely comment about those curved features now.

In our typical chassis designs, we run our chain in a very tight area between 2 metal plates. I'm concerned in our design (and in similar one's I've seen) that those tabs are sticking out way too much to be effective & not get snagged on those plates, or anything mounted inside those plates. (Bronze bushings, spacers, screw heads, etc...)

We had our frame spaced so tightly one year in terms of area between plates, that a rushed replacement socket head cap screw (rather than the original flat head screw) actually popped the chain right at the link in the finals match of a competition.

I love this design, but I'm just saying that if we were to use these, we would more than likely just use zip-ties, not use the rubber bands or o-rings (which I think will wear out even more quickly over a competition anyways and require more maintenence - even more so than the blocks themselves with the concerns Greg N. posted) & we would probably cut or shave those curved tabs right off.

Just a thought from someone with bad experience with a hardware vs chain matchup in a real world design application.

Of course, your results may vary. :cool:

Re: pic: Andymark's New Product
 

http://www.snapidle.com/

This website with a similar product has a picture that shows the concept. However for what it matters I endorse the AM product, might as well support a fellow FIRSTer!

Re: pic: Andymark's New Product
 

The Snapidle Mini appears to be the same kind of tensioner sold by McMaster-Carr (5973K1 or 5973K2, depending on the chain size). Those sell for about $30 each.

Re: pic: Andymark's New Product
 

As for the picture of this thing in action, I will take one tomorrow and upload it and why it is so effective:

-Lightweight
-Cheap
-No maintenance
-Easy Removal (We wasted so much time taking the snap ones on and off).
-Can be left floating or can be made stationary
-No lubrication



The zipties don't wear really, you could ideally go 7-8 matches without even worrying about the zip ties. As long as you cut the ends of the zip ties off. If the frame is really too tight. We used only one of the blocks then. We mounted it in between and made it stationary. If you upload a pic of your frame. I could give you solution. We had this problem when we were using the mcmaster carr ones 3 years ago.

Re: pic: Andymark's New Product
 

Having used the snap idle version I know how those are pulled together in order to keep the chain properly tensioned. With this you either use ty wraps or o-rings. My question is how easy is it to get enough tension on the ty-wrap without having to use a ty-wrap gun since most chassis do not have the room for it.

Re: pic: Andymark's New Product
 

I like the simplicity, but it puts too many things out of control for me, such as the slack between the two sides when the sprockets change directions would be undesireable in my opinion. Our method was swiped from 118 with nice tensioners that just involve tweaking a screw a little tighter. And the chain loops were stable and not whipping around all over the place.

the main reason they wouldn't work to well in our situation is the proximity to victors... so no whippage room was available, kinda cause the swerve drive. We may use them elsewhere though it looks like a solid product, congrats

efficiency wise ball bearing idler sprockets and pulling the drive/driven sprockets to adjust the chain wins vs sliding on plastic

Re: pic: Andymark's New Product
 

You could always tension these with a hose clamp if you wanted to.

Re: pic: Andymark's New Product
 

Now how cool is that? Can they mold your initials on it just for bragging rights?
Ah, so that's why our tensioners kept wearing out...:D

Seriously: I would have some concerns about stress on those hooks breaking them off. I'd want a bigger fillet, or even a small gusset, where the hook meets the body. (Then again, it's just a CAD drawing, Andy or Mark probably saw what I am seeing already, before committing to a mould).

Don

Re: pic: Andymark's New Product
 

This product looks great. I'm glad AndyMark was able to market these items at a cheaper price than what was on the market before. Tumbleweed used a set of those Snapidle Minis on the chain to the 'front' wheel. We went through these unfortunately quickly with the amount of driving the bots went through with practice and competition. The straps for the set we used would become easily worn and annoying to deal with. In order to take them off you actually had to take one side of the tensioner apart. I think zip-ties will be much more cost efficient for teams, along with just plain easier on the pit crews. I hope to see these in action some time this season!