Chief Delphi - AndyMark Teasing us

Page 5 of 5

Show 100 post(s) from this thread on one page

Chief Delphi (http://www.chiefdelphi.com/forums/index.php)

- General Forum (http://www.chiefdelphi.com/forums/forumdisplay.php?f=16)

- - AndyMark Teasing us (http://www.chiefdelphi.com/forums/showthread.php?t=70245)

R.C.	18-12-2008 20:53

Re: AndyMark Teasing us

Quote:

Originally Posted by D Collins (Post 785211)

From the new products page on the AndyMark website:

"In late January, we will have some 1/2" hex bore flanged ball bearings... yeah, you heard us right: hex bore bearings (just like FR8ZZ, but with a 1/2" hex bore)"

This brought a smile to my face. Thank you Mr. Baker!

Dude, Andy you are the man, makes all of our designs ten times easier. Just ask Craig!:ahh:

IndySam

19-12-2008 14:28

Re: AndyMark Teasing us

Question Andy
If I would like to build a Gen1 with the output gears on the outside of the trans instead of on the inside could I use the SS small cluster gear, shorten the spacers and substitute the new aluminum side plates?

Madison

30-12-2008 12:03

Re: AndyMark Teasing us

Hey Andy,

Are y'all still on track to offer those #25 sprockets with .5" diameter, keyed hubs? :)

Danke,

Cory	30-12-2008 12:22

Re: AndyMark Teasing us

Quote:

Originally Posted by Madison (Post 788368)

Hey Andy,

Are y'all still on track to offer those #25 sprockets with .5" diameter, keyed hubs? :)

Danke,

Same question, except 0.250" plain bore?

Andy Baker

30-12-2008 17:07

Re: AndyMark Teasing us

Quote:

Originally Posted by Madison (Post 788368)

Hey Andy,

Are y'all still on track to offer those #25 sprockets with .5" diameter, keyed hubs? :)

Danke,

Quote:

Originally Posted by Cory (Post 788374)

Same question, except 0.250" plain bore?

Yes, and yes... sorry for the delay on these. They will be available right after kickoff, at this time next week.

We had them done, but they were made with too fast of a feed speed, and the chain wrap was not right. So... we are fixing them now.

Andy

Andy Baker

01-02-2009 11:39

Re: AndyMark Teasing us

Here is an update on a few of these topics:

FR8ZZ-Hex bearings will be at AndyMark by the end of this week (Feb. 5th-6th). They are currently being shipped to us.

16 and 22 tooth, 25 series aluminum sprockets will be available again by Wednesday (Feb. 4th).

AM Planetary gearboxes will be available again by Wednesday (Feb. 4th).

I have just updated our New Products page, which has some other interesting things.

Sincerely,
Andy Baker

s_forbes

11-02-2009 13:33

Re: AndyMark Teasing us

Didn't see anyone else post it, but the hex bore bearing is now up on AM's site, with a picture: http://www.andymark.biz/am-0279.html

Quite the nifty little bearing, I bet it has a billion different uses! When are we going to see the "hex output shaft" option for the toughboxes?

MasonMM

11-02-2009 14:37

Re: AndyMark Teasing us

Andy,
Any plans for an unflanged hex bearing?

AndyB

11-02-2009 14:48

Re: AndyMark Teasing us

Quote:

Originally Posted by MasonMM (Post 818671)

Andy,
Any plans for an unflanged hex bearing?

Or other sizes (3/8" hex)?

All times are GMT -5. The time now is 14:26.

Page 5 of 5

Show 100 post(s) from this thread on one page