Pneumatics Programing
 

Anyone have any ideas about programing pneumatics in LabView?:confused:

Re: Pneumatics Programing
 

Here is a simple form of the compressor and controlling a solenoid from the trigger of joustick 2.

There is a "Solenoid with Compressor Example" too you can look at on the LabVIEW startup screen.

Re: Pneumatics Programing
 

You use the Solenoid Breakout and the Solenoid VIs

http://www.usfirst.org/uploadedFiles...s-Rev-0-5a.pdf go down to Solenoid Breakout. It plugs into one of the cRIO modules.

Re: Pneumatics Programing
 

Thanks for the help!!!:] :D

Re: Pneumatics Programing
 

I have a quick question, in the Advanced Framework, how do we get all the code parts (eg. USB 2.. or Solenoid 1.. or Relay 6)?.. were they just made up or are they in the WPI Robotics Library?

thanks for the help, the code samples were really helpful

Re: Pneumatics Programing
 

Those are enumerated in the LabVIEW FRC palettes.
You automatically get them when you wire a Constant to the WPI vi's, such as, Joystick Open.

Re: Pneumatics Programing
 

I looked at your example, but i am unable to tell how the program knows that it is to run off the trigger of joystick 2. In our setup, we have a third joystick used to control two motors and hopefully also used to control our solenoid with the trigger of joystick 3. any ideas?

Re: Pneumatics Programing
 

Does it help to know that button 1 is the trigger on the KOP joysticks?
Each of the joystick buttons has the number printed on it except for the trigger of course. :)
In that example the USB 2 joystick is opened, and button 1 (the trigger) is feed into and controls the solenoid.

If you want to use the trigger on joystick 3 instead, just change "USB 2" to "USB 3" in that example.
In normal usage you'd put all this in the same loop you use the joysticks to tank/arcade drive.

Re: Pneumatics Programing
 

This code will be used in the same loop as our tank drive setup, but i'm still a little confused. In the link you provided, there isn't a Joystick open .vi or anywhere to change the USB 2 to USB 3. I understand that the trigger is button one on the joysticks. In our setup, joysticks 1 and 2 run tank drive. Will i need to program the trigger of one of those joysticks?

I guess my question is, in the example that you provided, there never is a specified USB value. It goes from compressor open, to compressor start, to compressor stop and close.

Re: Pneumatics Programing
 

I think we're looking at different examples.
Take a look at the link to controlling a solenoid that was posted in another thread on the same topic.
CD doesn't allow me to repost it in this thread.

It uses "USB 2" on the left side of the diagram.

Re: Pneumatics Programing
 

ah yes, this solves my problem. Thanks a lot.

Re: Pneumatics Programing
 

one more question....do i need to place the code for my compressor and solenoid valves in the teleop case loop inside my while loop? or can i just place it in it's own while loop?

Re: Pneumatics Programing
 

You want the solenoid check inside your teleop loop, since that's where you are reacting to joystick commands.

The compressor you want operating in both autonomous and teleop modes so that goes elsewhere.
Really, the compressor Open and Start should be in the Begin.vi and the Close in Finish.vi. You need to add the compressor cluster information to RobotData.ctl so it can be used in the Finish.vi

P.S. I'm assuming by what you said that you're using the Advanced Framework. If you're using the Basic one instead it's a little different.

Re: Pneumatics Programing
 

thanks, that helps.

Re: Pneumatics Programing
 

Okay, I just sat down to program this setup and i realized that this is a timed function. How do I incorporate the timed function within my teleop loop without it affected the entire teleop loop?