Set computer to receive it's IP via DHCP?
 

On page 45.... in Section 1... of the Control System Manual it says, "set your computer to receive it's IP via DHCP". How do we do this?

Re: Set computer to receive it's IP via DHCP?
 

The DHCP settings are reached by going into your Network Connections -> Local Area Network Connection (right click)-> Properties -> TCP/IP

I hope this helps. This is also where you will set the static IP.

Re: Set computer to receive it's IP via DHCP?
 

OK- We have been there and set our static IP to 10.21.47.6 (our team # is 2147). Is their something we have to select to set the DHCP? I don't see anything referring to a DHCP in any of these screens?

Re: Set computer to receive it's IP via DHCP?
 

Set it to obtain IP address automatically. DHCP is the protocol by which it does that.

Re: Set computer to receive it's IP via DHCP?
 

Thanks! That did the trick.

Re: Set computer to receive it's IP via DHCP?
 

I have some trouble with that too..
I set the ip to get automatically and then open internet explorer and type in 192.168.1.250 as described in the manual.
Yet I cannot connect to the bridge...
Here is how the wires run
The cisco modem(wrt610n) is connected to the computer through ethernet cable. Then the ethernet cable from the linksys modem(wga600n) is connected to the cisco modem.
I don't know what the probem is so can anyone help?
Thank you for any kind of help.

Re: Set computer to receive it's IP via DHCP?
 

I belive you need to connect to the bridge wirelessly to be able to use it. 2 DHCP servers wired directly together is not the best idea in the world

Re: Set computer to receive it's IP via DHCP?
 

Try resetting the bridge to its factory settings by pressing the reset button for 20 seconds. I also unplugged and replugged the bridge to be sure it was reset.

Also, the 2 ethernet cables into the bridge have to be plugged into the "1,2,3, or 4" Ethernet jacks, not the jack labeled "Internet".

Re: Set computer to receive it's IP via DHCP?
 

I tried it it but still it does not work..
In the manual is says type 192.2689.1.250 and we tried it but id did not work..
Realizing that that it may be a defaut setting we connected the brigde(wga600) directly to the computer and ran ipconfig on command propt, got the ip and default gateway, ran them on a web browser but it still did not work.. we cannot connect to the bridge...
Any suggestions???

Re: Set computer to receive it's IP via DHCP?
 

Sorry for a double post but the ip was 192.168.1.250..
it was little typing error

Re: Set computer to receive it's IP via DHCP?
 

Try connecting your PC directly to the WGA600N via Ethernet cable.
Set a static IP on your PC of 192.168.1.6, netmask 255.0.0.0
Then try browsing to 192.168.1.250

Re: Set computer to receive it's IP via DHCP?
 

We already tried...

Re: Set computer to receive it's IP via DHCP?
 

Did you disable your PC wireless if you have it?

Re: Set computer to receive it's IP via DHCP?
 

Im having trouble with browsing the bridge. We got into the configuration page and did all the steps like rebooting but now when we try to get to the configuration page again, it says connection was reset. What do we do.

Re: Set computer to receive it's IP via DHCP?
 

Did you change the bridge IP address when you rebooted it?

Did you then change your PC's IP address to be compatible with the new bridge IP address before you tried to reconnect?

That's the most common snag.

I presume you are hard-cabled from the PC to the bridge while doing this, or are you going through the router too?

Re: Set computer to receive it's IP via DHCP?
 

How do you make the bridges new ip address to be compatible with your computer.

Re: Set computer to receive it's IP via DHCP?
 

If you connect and change the bridge IP to be compatible with the preferred robot setup, then after rebooting the bridge you must make your PC IP also compatible with the robot setup before you will be able to talk with the bridge again.

Assuming your PC is connected directly to the bridge...
After you set the bridge IP to 10.8.42.1
you must reset the PC IP to 10.8.42.6
then you should be able to browse to the bridge again.

Did you start from resetting both the bridge and router to factory defaults, or are you just resetting the bridge, since the router is probably fine already?

Re: Set computer to receive it's IP via DHCP?
 

Hey, I've now configured the bridge and the router but the bridge doesn't have a green on the driver station

Re: Set computer to receive it's IP via DHCP?
 

Go through a similar process to setup the router.

After you reset the router did you:

• Directly connect your PC to it with an Ethernet cable
• Change your PC's IP address to 192.168.1.6 (or you can use DHCP)
• Browse to IP 192.168.1.1

Re: Set computer to receive it's IP via DHCP?
 

Do you have a green cRIO status?

The most likely reason for the bridge not being green is the IP address could be off (not 10.8.42.1). The green status is only if a device with that IP is found. Or your PC's IP address is not based on the same team number (10.8.42.5 for the Driver Station PC).

Re: Set computer to receive it's IP via DHCP?
 

Hey I've reset the router and the bridge, followed the steps again, and tried connecting from the classmate to the router. Then tried connecting to the bridge but still no luck. We can get into the router and into the bridge but can't connect to the bridge from the router. Anyone know what to do?

Re: Set computer to receive it's IP via DHCP?
 

Does anyone know how to configure a router with Firmware Version: v1.0.04. Also, is it possible to downgrade it.