1/2" gap in bumpers, is this acceptable?
 

We have assembled our robot bumpers on our rectangular robot. The front and back bumpers are as wide as the robot. The left and right side foam extends so that it is flush with the outside edge of the front and rear bumpers. This has created a 1/2" gap between the side bumpers and the front/rear bumpers. (Caused by the plywood backing.)

Do we have a potential problem passing inspection? We think we met the rule for complete coverage, but I don't want to be scrounging pool noodles during our Week 1 competition in Rochester.

Re: 1/2" gap in bumpers, is this acceptable?
 

This will not be acceptable at inspection.
You will have to fill that area with pool noodle to meet the rule intent.
I suggest that you cut the noodles at the end of the wood and then add a cut section of noodle there on end as the rules allow. When you re-wrap you should no-longer have gap.

Re: 1/2" gap in bumpers, is this acceptable?
 

Interesting question... my first response was "no way could that be a problem". From the photo the bumpers look sturdy, safe, and fully capable of fulfilling the role of being a bumper, and the 1/2" gap is insignificant to their overall purpose.

But R07-L and the related diagram 8-2, specify that the "corners must be filled".

So yeah... you could have a problem. Thanks for asking the question... we haven't built our bumpers yet, so we'll pay attention to this when we put them together this year. I don't think its likely to be a big problem from a practical point of view (I doubt many inspectors would call it... but they could), but given that you've got two weeks to get the bumpers up to spec right now, that's probably more fun than doing it in two hours on a Thursday morning.

Jason

Re: 1/2" gap in bumpers, is this acceptable?
 

That gap seems like the amount of space a somewhat flexible bumper could easily unintentionally leave if slightly jolted or something. Or, to be more clear, I'm pretty sure I've seen robots pass inspection without the two fabrics exactly touching all the time.

That being said, it's not too long of a fix.

Re: 1/2" gap in bumpers, is this acceptable?
 

That's... not a 1/2" gap. More like a 1"-2" gap.

I'd go with Peter's suggestion: unwrap the end, cut the noodles, and replace with a vertical section of noodle. You've got time now (and presumably some extra noodle sections laying around), so fix it now and fix it right so you don't have to fix it in a big hurry at the competition.

Re: 1/2" gap in bumpers, is this acceptable?
 

It's 1/2" wide gap that is 2" long.

We have oodles of noodles (oh how long have I waited to post that!) around the shop, so we'll do a quick fix and upgrade the plans for the "red" set.

Thanks to all that replied either here or via PM's.

Re: 1/2" gap in bumpers, is this acceptable?
 

You didn't follow the instructions exactly, and this is the result. (And I don't mean that to sound condescending, I'm just stating a fact.)

Notice the corner labeled "Not OK" in Figure 8-2. Also notice the word "filled" in the rules. I never stopped to think about this before, because the last year I actually worked with the bumpers was before the filled corner rule came into effect. My first reaction would have been, easy, just make the noodles longer and it will work. I guess you've inadvertently proved I would have been wrong. Using a 5" vertical noodle works because it naturally moves around the end of the backer board, whereas an extended horizontal noodle ends up sticking out straight.

Unfortunately I think you'll have to fix it.

Edit: You might also be able to get away with lengthening the noodles on the "butted" end to achieve full corner protection, but you take a risk of that not passing because it doesn't match one of the three ways mentioned in the rules. I think I recall a Q&A last year that said it was OK. If this is your solution, you might ask Q&A, because last year's rules don't apply to this year's game.

Re: 1/2" gap in bumpers, is this acceptable?
 

Foster,
As much as I hate to go against Gary, the intent of the the bumper rule is to have no hard parts in the corners that can contact another robot. At first it would seem like this picture is a violation but I think if you hit the upper right corner of the bumpers, you would not be able to hit the hard parts of the two bumper sections nor the corner of the frame. Of particular note are these paragraphs in R07...
A. BUMPERS must provide complete protection of the entire FRAME PERIMETER of the ROBOT (i.e. BUMPERS must wrap entirely around the ROBOT). The BUMPERS must be located entirely within the BUMPER ZONE when the ROBOT is standing normally on a flat floor, and must remain there (i.e. the BUMPERS must not be articulated or designed to move outside of the BUMPER ZONE).
and
N. “Hard” parts of the BUMPER (i.e. plywood backing, fastening system, and clamping angles) may extend up to a maximum of one inch beyond the FRAME PERIMETER. “Soft” parts of the BUMPERS (i.e. pool noodles and cloth covering) may extend up to 3½ inches beyond the FRAME PERIMETER.

The only thing that appears to be a little long is the top bumper section. The hard part cannot extend past the corner of the frame by more than an inch. In this view I cannot tell whether the wrap of cloth is over a hard part or not. Touch would be the only way I could tell.

Re: 1/2" gap in bumpers, is this acceptable?
 

Does your plywood overlap the corner and butt your other corner, if it does you are also in violation.:eek:

Re: 1/2" gap in bumpers, is this acceptable?
 

I agree with Al, I believe the bumpers meet the intention of the rule. If you were at his event, he'd pass you (subject to the hard parts, which to me looks like you might be OK, but like Al I'd have to feel it). But what will the inspector at your event say? Do you want to risk it?

Re: 1/2" gap in bumpers, is this acceptable?
 

What I'm concerned about is there is a segment of bumper left flapping in the breeze. This could potentially become snagged on something. I hate to say it, but legal or not, I would not want to compete with a bumper quite like this. You have time, go ahead and redo it a bit.

Re: 1/2" gap in bumpers, is this acceptable?
 

There isn't a segment "flapping". The part that is sticking out is the two 2" pool noodles wrapped in fabric.

We have noodle bits cut to fill in the gap and our Master Bumper Builder will do the quick fix this weekend.

Thanks again for all the input!

Re: 1/2" gap in bumpers, is this acceptable?
 

New improved bumpers showing better fit and the new spiffy red color. We put another section of foam in the bumper end.

Re: 1/2" gap in bumpers, is this acceptable?
 

Of note here - in some previous years, it was NOT required to have soft bumper material in the corners. Specifically, i know our first year (2007) we build our bumpers with no material at all in the corners, and they were perfectly legal.

Since then, we've cut all of our pool noodles at 45 degrees to fill the corners nicely.

Re: 1/2" gap in bumpers, is this acceptable?
 

we do too, i think. (BTW, never leave the robot supported by it's bumpers for an extended period of time, we did that to last year's bot recently, and the bumpers are squished down to half their normal size)