Chief Delphi

Chief Delphi (http://www.chiefdelphi.com/forums/index.php)
-   Extra Discussion (http://www.chiefdelphi.com/forums/forumdisplay.php?f=68)
-   -   pic: Enigma Wheel (http://www.chiefdelphi.com/forums/showthread.php?t=86494)

kgzak 08-08-2010 13:01

pic: Enigma Wheel
 

Rion Atkinson 08-08-2010 13:09

Re: pic: Enigma Wheel
 
Wow... It's been awhile since I've been on here... Finally something I'm semi qualified to speak about. Semi.

First off, the CAD looks very nice. And the wheel is a decent design, except for the loop on the end of the spokes. It is very likely to snap there. And the part after it contacts the wheel is just adding weight.

Any chance of a different view angle? (If you have it on a picasa or photobucket, something like that?)
How wide is the wheel?
What's the width of the spokes? The depth?
Whats the bore diameter?

-Rion

CalTran 08-08-2010 13:54

Re: pic: Enigma Wheel
 
Quote:

Originally Posted by Formerly Famous (Post 971163)
And the wheel is a decent design, except for the loop on the end of the spokes. It is very likely to snap there. And the part after it contacts the wheel is just adding weight.

I dunno about their actual usage plan for the wheel is for, but I'm guessing that it'd be for more show then function.

Hawiian Cadder 08-08-2010 14:24

Re: pic: Enigma Wheel
 
i don't think the spokes will break, if the center bore is .5 in then those spokes are pretty thick. if you are planning to use these in a 6wd robot then i think it should be fine, as longs as there are no bumps in next years game.

EricVanWyk 08-08-2010 15:52

Re: pic: Enigma Wheel
 
Looks like fun!

If you have an experienced mechanical mentor available, ask her to show you how to do a "Finite Element Analysis" or to simulate what types of stresses will develop when you load it. This design should show some very interesting and informing results.

gblake 08-08-2010 16:26

Re: pic: Enigma Wheel
 
Quote:

Originally Posted by EricVanWyk (Post 971179)
Looks like fun!

If you have an experienced mechanical mentor available, ask her to show you how to do a "Finite Element Analysis" or to simulate what types of stresses will develop when you load it. This design should show some very interesting and informing results.

Do what Eric suggests to analyze a new design that ignores embedding question marks or other decorations into the wheel. Just make the result a strong, light wheel.

Then... create a light, snap-on decorative hubcap that fits onto that wheel and adds only trivial weight to the completed assembly. The hubcap's wow-factor is limited only by your imagination (and the audiences' ability to appreciate fine art :)).

kgzak 08-08-2010 16:40

Re: pic: Enigma Wheel
 
Quote:

Originally Posted by Formerly Famous (Post 971163)
Wow... It's been awhile since I've been on here... Finally something I'm semi qualified to speak about. Semi.

First off, the CAD looks very nice. And the wheel is a decent design, except for the loop on the end of the spokes. It is very likely to snap there. And the part after it contacts the wheel is just adding weight.

Any chance of a different view angle? (If you have it on a picasa or photobucket, something like that?)
How wide is the wheel?
What's the width of the spokes? The depth?
Whats the bore diameter?

-Rion


I'll get some other views of it. As I said my computer wasn't cooperating with me.


Quote:

Originally Posted by CalTran (Post 971167)
I dunno about their actual usage plan for the wheel is for, but I'm guessing that it'd be for more show then function.

Yup, I wasn't planning on anything with these wheels except to learn a little about CAD.

Quote:

Originally Posted by EricVanWyk (Post 971179)
Looks like fun!

If you have an experienced mechanical mentor available, ask her to show you how to do a "Finite Element Analysis" or to simulate what types of stresses will develop when you load it. This design should show some very interesting and informing results.

We have one mentor that does a lot of 2D CAD, I don't know how much 3D CAD he does. We have another College Student that took a class in it so I'll ask both of them when we start meeting again.

Quote:

Originally Posted by gblake (Post 971180)
Do what Eric suggests to analyze a new design that ignores embedding question marks or other decorations into the wheel. Just make the result a strong, light wheel.

Then... create a light, snap-on decorative hubcap that fits onto that wheel and adds only trivial weight to the completed assembly. The hubcap's wow-factor is limited only by your imagination (and the audiences' ability to appreciate fine art :)).

I'll look into doing something like that.


Edit:
Wheel is 1.5in deep, 6in wide
Spokes are .5in deep, .25in wide
Any other measurements you would like?

Chris is me 08-08-2010 17:13

Re: pic: Enigma Wheel
 
I think it would be more reasonable, if you wanted the question marks, to make fairly large spokes and use the question mark shape as a lightening pattern.

kgzak 08-08-2010 18:30

Re: pic: Enigma Wheel
 
Quote:

Originally Posted by Chris is me (Post 971183)
I think it would be more reasonable, if you wanted the question marks, to make fairly large spokes and use the question mark shape as a lightening pattern.

I was going to try that next :p

Chris is me 08-08-2010 18:51

Re: pic: Enigma Wheel
 
Another nitpick: You're going to need to cut out a groove for the bearings in your wheel.

Rion Atkinson 08-08-2010 20:18

Re: pic: Enigma Wheel
 
Quote:

Originally Posted by kgzak (Post 971181)
Yup, I wasn't planning on anything with these wheels except to learn a little about CAD.

It's always good to start with CAD early by playing around with it and doing small projects. It makes it a lot easier come build season.

Quote:

Wheel is 1.5in deep, 6in wide
Spokes are .5in deep, .25in wide
Any other measurements you would like?
Okay, yeah those spokes wont break at that size. Though when you say that the wheel is 6in wide I assume you mean the diameter is 6 inches?

Are you running Inventor? I haven't been able to get a hold of Solidworks or Inventor recently so I can't remember which one has the 3 axis in the bottom that looks like that.

New picture edit: I don't know if the spokes have enough contact with the wheel. I also think you may be ale to pull weight out of the hub there.

kgzak 08-08-2010 20:53

Re: pic: Enigma Wheel
 
Quote:

Originally Posted by Formerly Famous (Post 971190)
It's always good to start with CAD early by playing around with it and doing small projects. It makes it a lot easier come build season.



Okay, yeah those spokes wont break at that size. Though when you say that the wheel is 6in wide I assume you mean the diameter is 6 inches?

Are you running Inventor? I haven't been able to get a hold of Solidworks or Inventor recently so I can't remember which one has the 3 axis in the bottom that looks like that.

New picture edit: I don't know if the spokes have enough contact with the wheel. I also think you may be ale to pull weight out of the hub there.

I was planning on pulling weight out of the hub. I have a new design that I will be posting soon. It's what Chris is me was suggesting.

Rion Atkinson 09-08-2010 13:48

Re: pic: Enigma Wheel
 
Quote:

Originally Posted by kgzak (Post 971192)
I was planning on pulling weight out of the hub. I have a new design that I will be posting soon. It's what Chris is me was suggesting.

I would also advise putting a groove on the outside part of the wheel. It will keep the tread from sliding to one side or the other.

JesseK 09-08-2010 15:05

Re: pic: Enigma Wheel
 
I'm with Blake on this one. There are options to make it very aesthetically pleasing using a hub cab, including annodizing the wheel and the decoration different colors. Even doing this to an AM Plaction wheel and no plate annodization could be 'pretty'.

Of course the drive train needs to be designed such that the wheels can be seen to begin with, otherwise wheel aesthetics are for naught. In 2008 & 2009 aesthetic wheel design proved futile due to bumper rules, which is another thing to keep in mind during build season.

Brandon Holley 09-08-2010 15:22

Re: pic: Enigma Wheel
 
Quote:

Originally Posted by JesseK (Post 971216)
I'm with Blake on this one. There are options to make it very aesthetically pleasing using a hub cab, including annodizing the wheel and the decoration different colors. Even doing this to an AM Plaction wheel and no plate annodization could be 'pretty'.


I'm with you guys as well.

However, it seems he is doing this as an exercise in CAD, which is perfectly fine by me. Its nice to design something you are familiar with to start (like an FRC wheel of sorts).

Keep up the good work, and keep trying new things.

Brando


All times are GMT -5. The time now is 04:00.

Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi