pic: 3729's minibot
 

Re: pic: 3729's minibot
 

Looks great! How fast does it go?

Re: pic: 3729's minibot
 

Did you have any issues with the cantilevered shafts hanging off each motor? What kind of times are you running?

Looks good!

-Brando

Re: pic: 3729's minibot
 

is this the only view we can see wats the back look like

Re: pic: 3729's minibot
 

No issues with the cantilevered shafts. The motors are mounted on 1/16 inch Lexan which allows them to flex a little. This afternoon the minibot was climbing in 1.8 secs.

Re: pic: 3729's minibot
 

How much does it weigh?

Re: pic: 3729's minibot
 

2,4 lbs

Re: pic: 3729's minibot
 

just wondering is the mount between the motors support the battery

Re: pic: 3729's minibot
 

You can get through approximately a regional on cantilevered shafts.

I would recommend supporting them fully but this will win you matches as is.

Re: pic: 3729's minibot
 

2826 uses cantilevered shafts similar to this made from 1/4-20 grade 2 bolts arbor pressed onto the motor shaft. We were really worried about this being an issue at fist, so we built 3 bots. Since, we have had at least 75 successful deploys with this design in practice and we just won the Wisconsin regional (thanks 111 and 2702) where we deployed successfully 12 of 16 matches and probably could go at least through St Louis with the same minibot.

Re: pic: 3729's minibot
 

What type of material is used for traction on the shafts? I've heard that the surgical tubing won't work, so curious what material (and where to get it) was used. This is a great design.

Re: pic: 3729's minibot
 

Try it.

Re: pic: 3729's minibot
 

What are you using for switches?

Re: pic: 3729's minibot
 

That looks a lot like our minibot :)

Re: pic: 3729's minibot
 

A few answers: The shafts are 2 inch long by 3/8 inch aluminum rod drilled with a 3/32 drill. They are then pressed on with an arbor press. The friction material is 3/8 inch OD Latex stretched on after running hot water over it for a few seconds. The white object just below the motors is a pole guide made from a 1 1/2 pvc pipe fitting. In addittion two magnets help hold the minibot to the pole. The battery is held in position between two pieces of 1/2 aluminum tubing. Inside this tubing are guide pins attached to the deployment tray. There are two on/off lamp switches and one limit switch that control the motors. The first switch turns on the motors when the bot contacts the pole. When the second switch contacts the top of the tower it shifts the motor to half power so the bot will slowly decend the pole. A limit switch on the bot's base then turns off power when it comes down the pole and makes contact with the base. Weight management of the minibot is essential. Let the bot get to heavy and you'll smoke the motors.

Re: pic: 3729's minibot
 

How exactly are you mounting your magnets?

Re: pic: 3729's minibot
 

Two magnets each directly opposite each other sandwitching the 1/16 inch Lexan between them. Polycarbonate glue is used to keep them in position. This puts one surface of the magnet about 1/16 inch above the surface of the pole.

Re: pic: 3729's minibot
 

Are lamp switches legal? The rules say only "2 common household lightswitches"

Re: pic: 3729's minibot
 

Yes, if they are sold as a "light switch" for household use. Read Team Update 12 for the full interpretation.

Re: pic: 3729's minibot
 

Are lamp switches legal?

Re: pic: 3729's minibot
 

From TU #12

A note about “light switches” permitted on the MINIBOT:
We have previously stated in the Q&A that “light switches” are only “light switches” if they are commonly used in a wall mounting box. Rule R92-N, however, uses the language “common household light switches”; which can have a much broader interpretation. Given the discrepancy in specificity between R92 and the Q&A statements, we defer to the manual. Therefore, “light switches” permitted on the MINIBOT are not confined to those used in wall mounting boxes; anything sold as a “light switch” for household use is allowed. The Q&A answers will be revised.

Lamp switch = light switch and yes you can buy them at Home Depot with the rest of the "light switches"

Re: pic: 3729's minibot
 

Be careful about aluminum rod pressed onto the motor shaft unless you are using a very strong grade of aluminum. We used 6061 at first and it was a miserable failure. We ended up with 1/4-20 steel bolts as shafts and it works great.

Re: pic: 3729's minibot
 

Thanks. Sorry I asked twice I didn't think it posted the first time.

Re: pic: 3729's minibot
 

How did you attach the bolts to the motor shaft?

Re: pic: 3729's minibot
 

By drilling a hole in the center of the bolt that is an interference fit and carefully pressing the motur shaft into it

Re: pic: 3729's minibot
 

How do you get the switches to change the motors to half power?

Re: pic: 3729's minibot
 

We used a light switch to hook a 4 ohm resistor in series with the motors. Since all the recent problems with switches and getting them thru inspection we're using the KoP limit switches to short the motors to decend. It's working great.

Re: pic: 3729's minibot
 

Resistors aren't allowed on the minibot, by the way.

Re: pic: 3729's minibot
 

Thanks for the answers!

1 last question, how do you secure the surgical tubing to the motor shaft? We were able to get it on, but it keeps sliding off. Thanks!

Re: pic: 3729's minibot
 

It will stay on if:
1. You have enough contact area (>1" has worked for me)
2. The ID of the tubing is the same, or smaller than the OD of the shaft

Chances are it will take some finger strength to get the surgical tubing on without a lubricant. Its what I have been doing for weeks.
Some teams have said they use warm water or rubbing alcohol. For whatever reason we can't get warm water in our building so I haven't been able to try it.

Now that you know, can you explain why the tubing behaves this way?

Re: pic: 3729's minibot
 

We oversized our shafts to get the tubing to stick. A ~.275-.28 shaft for 1/4" ID surgical tubing worked great for us.

Re: pic: 3729's minibot
 

Nice minibot! Looks like it is capable at climbing poles. :p

My favorite comment about ours when it was getting expected was "Where's the rest of it?" :p

Re: pic: 3729's minibot
 

Chuck! I PMed you and nice minibot. Nice to see you're still part of a FRC team. (Testa told me what happen with 1583).

Re: pic: 3729's minibot
 

Thanks Jeffy! We think the tubes were coming off because we tried testing the minibot too soon after we used the rubbing alcohol as a lubricant. Everything is working great now!