Go to Post I had a few jokes about the illness and germs at some of the competitions, but I don't want to spread them around. - tsaksa [more]
Home
Go Back   Chief Delphi > Old Forum Archives > 2001
CD-Media   CD-Spy  
portal register members calendar search Today's Posts Mark Forums Read FAQ rules

 
 
Thread Tools Rate Thread Display Modes
  #1   Spotlight this post!  
Unread 24-06-2002, 00:20
archiver archiver is offline
Forum Archival System
#0047 (ChiefDelphi)
 
Join Date: May 2001
Location: Pontiac, MI
Posts: 21,214
archiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond repute
Re: Connecting hub sprockets to shafts

Posted by Patrick Dingle at 2/5/2001 11:36 PM EST


Other on team #639, Red B^2, from Ithaca High School and Cornell University.



Thanks to all who posted advice regarding connecting the sprockets to shafts. After some hard work trying to convince others on the team, we took the advice of Raul and Paul. We were able to machine a hole centered exactly tangential to the inner circumference of the hub... We even managed to cram a square peg (keystock) in a round hole! Anyway, it appears to work very nicely on our drive system and I see no possible way of breaking it.

Thanks again!

Patrick


__________________
This message was archived from an earlier forum system. Some information may have been left out. Start new discussion in the current forums, and refer back to these threads when necessary.
  #2   Spotlight this post!  
Unread 24-06-2002, 00:20
archiver archiver is offline
Forum Archival System
#0047 (ChiefDelphi)
 
Join Date: May 2001
Location: Pontiac, MI
Posts: 21,214
archiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond repute
Re: Connecting hub sprockets to shafts

Posted by PAUL GIANNOSA at 2/6/2001 10:19 PM EST


Engineer on team #27, TEAM RUSH, from OSMTECH and TEXTRON AUTOMOTIVE CO..


In Reply to: Re: Connecting hub sprockets to shafts
Posted by Patrick Dingle on 2/5/2001 11:36 PM EST:



: Thanks to all who posted advice regarding connecting the sprockets to shafts. After some hard work trying to convince others on the team, we took the advice of Raul and Paul. We were able to machine a hole centered exactly tangential to the inner circumference of the hub... We even managed to cram a square peg (keystock) in a round hole! Anyway, it appears to work very nicely on our drive system and I see no possible way of breaking it.

: Thanks again!

: Patrick
HEY PAT. I'M GLAD YOU DECIDED TO TRY THE PIN SET UP. YOU DON'T HAVE TO USE KEY STOCK THOUGH, A HARDEND AND GROUND DOWEL PIN WORKS WELL TOO. AND FITS IN ROUND HOLES A LITTLE EASIER. GOOD LUCK THIS YEAR AND I HOPE TO SEE YOU IN THE PITS. I'LL BE WITH THE TEAM WHOSE BOT IS HAVING A NERVOUS BREAK DOWN FROM THE SHEAR ENORMITY OF THE TASKS FOR WHICH WE ARE FORCING TO DO THIS YEAR!! PMGRACER



__________________
This message was archived from an earlier forum system. Some information may have been left out. Start new discussion in the current forums, and refer back to these threads when necessary.
 


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
modifying sprockets gail OCCRA 3 05-10-2002 12:13
shafts, gears and wheels.... archiver 2001 13 24-06-2002 04:09
Connecting hub sprockets to shafts archiver 2001 18 24-06-2002 00:04
5/16" cold steel shafts... archiver 2001 3 23-06-2002 23:17
Which form of connecting a rod to a wheel is the best? SilverStar Technical Discussion 2 27-03-2002 20:30


All times are GMT -5. The time now is 14:55.

The Chief Delphi Forums are sponsored by Innovation First International, Inc.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi