Go to Post I never had any doubt; good people who do good quality work will always prosper. - Gary Dillard [more]
Home
Go Back   Chief Delphi > Old Forum Archives > 2000
CD-Media   CD-Spy  
portal register members calendar search Today's Posts Mark Forums Read FAQ rules

 
 
Thread Tools Rate Thread Display Modes
  #1   Spotlight this post!  
Unread 24-06-2002, 00:08
archiver archiver is offline
Forum Archival System
#0047 (ChiefDelphi)
 
Join Date: May 2001
Location: Pontiac, MI
Posts: 21,214
archiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond repute
hieght of the scoring ramp

Posted by Pat.

Student on team #101, STRIKER, from St. Patrick High School and LoDan Electrtonics.

Posted on 10/17/2000 9:59 AM MST



In the diagram of the scoring ramp, they do not asign a measurement to the height of the back. Does anybody know the angle of the ramp. If so, please respond.


__________________
This message was archived from an earlier forum system. Some information may have been left out. Start new discussion in the current forums, and refer back to these threads when necessary.
  #2   Spotlight this post!  
Unread 24-06-2002, 00:08
archiver archiver is offline
Forum Archival System
#0047 (ChiefDelphi)
 
Join Date: May 2001
Location: Pontiac, MI
Posts: 21,214
archiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond repute
Re: hieght of the scoring ramp

Posted by Nate Smith.

Other on team #66, GM Powertrain/Willow Run HS, from Eastern Michigan University and GM Powertrain.

Posted on 10/17/2000 12:47 PM MST


In Reply to: hieght of the scoring ramp posted by Pat on 10/17/2000 9:59 AM MST:



: In the diagram of the scoring ramp, they do not asign a measurement to the height of the back. Does anybody know the angle of the ramp. If so, please respond.

The height of the peak is approx. 6 inches, according to one of Joe's posts earlier today...linked to below. Also, the angled surface of the ramp is made of a 48x48 piece of plywood(again from Joe's post). This should give you the information you need to calculate the angle. Hope this helps...

Nate
__________________
This message was archived from an earlier forum system. Some information may have been left out. Start new discussion in the current forums, and refer back to these threads when necessary.
 


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Robot/Goal scoring: Official Answer Mike Martus Mike Martus OCCRA 6 21-10-2003 23:51
A question about scoring.. Stack hieght... mike325 General Forum 7 09-01-2003 09:30
Pulling robot off ramp legal? archiver 2000 2 24-06-2002 00:14
scoring ramp dimensions archiver 2000 3 24-06-2002 00:13
Technical question about ramp balancing archiver 2001 5 23-06-2002 22:29


All times are GMT -5. The time now is 04:53.

The Chief Delphi Forums are sponsored by Innovation First International, Inc.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi