Go to Post No matter what route you choose, it's always a good idea to keep Mike Walker's cell phone on speed dial. - Joe Ross [more]
Home
Go Back   Chief Delphi > Old Forum Archives > 2001
CD-Media   CD-Spy  
portal register members calendar search Today's Posts Mark Forums Read FAQ rules

 
 
Thread Tools Rating: Thread Rating: 2 votes, 5.00 average. Display Modes
  #1   Spotlight this post!  
Unread 23-06-2002, 23:10
archiver archiver is offline
Forum Archival System
#0047 (ChiefDelphi)
 
Join Date: May 2001
Location: Pontiac, MI
Posts: 21,214
archiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond repute
Pneumatics electrical wiring and programming

Posted by Dan Grostick at 1/18/2001 10:08 AM EST


Engineer on team #267, Demolition Squad, from North Broward Prep / St. Andrews.



I've posted information (in the White Papers section) on the electrical wiring and programming of the pneumatics subsystem. I want to share my experiences programming the pneumatics demo board shown at the First kickoff.

Dan Grostick (267)


__________________
This message was archived from an earlier forum system. Some information may have been left out. Start new discussion in the current forums, and refer back to these threads when necessary.
  #2   Spotlight this post!  
Unread 23-06-2002, 23:10
archiver archiver is offline
Forum Archival System
#0047 (ChiefDelphi)
 
Join Date: May 2001
Location: Pontiac, MI
Posts: 21,214
archiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond reputearchiver has a reputation beyond repute
Comment out the relay line in default program

Posted by Vince Wilczynski at 1/20/2001 8:15 PM EST


Engineer on team #124, Whalers, from New London / Montville/ Williams School and Notheast Utilities / US Coast Guard Academy.


In Reply to: Pneumatics electrical wiring and programming
Posted by Dan Grostick on 1/18/2001 10:08 AM EST:



Thanks Dan.
One note, make sure you comment out the relay5 lines in the default program as noted below:
'relay5_fwd = p1_sw_aux1 'Port 1 Aux1 = Relay 5 Forward
'relay5_rev = p1_sw_aux2 'Port 1 Aux2 = Relay 5 Forward
/


__________________
This message was archived from an earlier forum system. Some information may have been left out. Start new discussion in the current forums, and refer back to these threads when necessary.
 


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Error found in programming for the pump and pressure switch sjharobotics Programming 4 06-02-2002 17:46


All times are GMT -5. The time now is 02:38.

The Chief Delphi Forums are sponsored by Innovation First International, Inc.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi