Linear Actuator for Lifting

[beemgruem]

Hello Everyone!

My team considers using Linear Actuators to climb the pyramid. Are we allowed to use Linear Actuators if it does not violate the electrical and pneumatic rules?

Thanks!

[PAR_WIG1350]

Pre-made electrical linear actuators likely include non-legal motors. They would have to be modified to operate with one or more of the legal motors listed in R32.

If you are using a lead screw, acme screw, or ball screw, without a motor, It should be legal provided you drive it with a legal motor and no other rules are violated.

NOTE: This is my interpretation of the rules and is not official. The only way to get an official answer is via the Q&A system.

[captianjroot]

My team is considering using a linear actuator to raise/lower a turret. Are there any other limitations regarding size of the actuator?

[IndySam]

Originally Posted by captianjroot

My team is considering using a linear actuator to raise/lower a turret. Are there any other limitations regarding size of the actuator?

The only limits are : #1 must use a legal motor, #2 must fit into starting configuration #3 cost.

[Al Skierkiewicz]

Begum,
If you would like to PM me with the part number I can give you my opinion off line. Otherwise, you might want to pose the question to the Q&A for an official response.

[Tangert]

Depending on the weight of your bot pneumatic linear slide actuator will probably not lift it. We tried it today with a 110 Lb weight and 250 MM and 300MM actuators neither would handle a vertical lift. The other thing to realize is that linear actuators always stay the same length. which may make it difficult to use for climbing.

[MentorPrice]

They are not allowed in the competition because of illegal parts and the pre-made nature of it.

[Al Skierkiewicz]

Originally Posted by MentorPrice

They are not allowed in the competition because of illegal parts and the pre-made nature of it.

?????
Explain please.

[Kevin Thorp]

A linear actuator is a commercial off the shelf (COTS) item, so it should be okay, as long as you use an approved motor on it (Table 4-1), and the "fair market value" does not exceed $400 (Rule 4.1.3).

[Jim Wilks]

Originally Posted by Kevin342

A linear actuator is a commercial off the shelf (COTS) item, so it should be okay, as long as you use an approved motor on it (Table 4-1), and the "fair market value" does not exceed $400 (Rule 4.1.3).

Since this is in the pneumatics section, we are talking about pneumatic linear actuators. Thus, no motor is involved.

[Kevin Thorp]

Rule R78 in Section 4 states you can use a pneumatic cylinder. A linear actuator is just a guided pneumatic cylinder, so I think you're okay.

However it might be difficult to find one with enough force for under $400. Remember, we can only use 60 psi, so if you needed 150 lbs force (robot, battery, bumpers & a safety margin) you'd the need piston area to be 2.5 square inches (150/60). That's 1.78" diameter or bore. The next common size is a 2" bore, but those are very expensive, WAY over the $400 limit.

Here are a few listed on Mcmaster Carr.

[Saberbot]

Originally Posted by Kevin342

Rule R78 in Section 4 states you can use a pneumatic cylinder. A linear actuator is just a guided pneumatic cylinder, so I think you're okay.

However it might be difficult to find one with enough force for under $400. Remember, we can only use 60 psi, so if you needed 150 lbs force (robot, battery, bumpers & a safety margin) you'd the need piston area to be 2.5 square inches (150/60). That's 1.78" diameter or bore. The next common size is a 2" bore, but those are very expensive, WAY over the $400 limit.

Here are a few listed on Mcmaster Carr.

You can get free cylinders, up to 2"x36" in the KOP via the Bimba PDV.

[Kevin Thorp]

Originally Posted by Saberbot

You can get free cylinders, up to 2"x36" in the KOP via the Bimba PDV.

Yup, and you can use a Bimba cylinder to build your own linear actuator. It probably won't be as precise as a COTS linear actuator, but you don't need precise to climb pipes.

[G Fawkes]

Originally Posted by Saberbot

You can get free cylinders, up to 2"x36" in the KOP via the Bimba PDV.

FYI -Two years ago, shortly after kickoff, we ordered 2"x24" cylinders from Bimba with the PDV and they arrived the Saturday of the final build weekend.

The smaller diameter ones have always arrived quickly.

[Saberbot]

Originally Posted by G Fawkes

FYI -Two years ago, shortly after kickoff, we ordered 2"x24" cylinders from Bimba with the PDV and they arrived the Saturday of the final build weekend.

The smaller diameter ones have always arrived quickly.

Thanks, we'll have to keep that in mind. The 2x8" ones we ordered are pretty integral to our design.