|
|
|
![]() |
|
|||||||
|
||||||||
![]() |
|
|
Thread Tools |
Rating:
|
Display Modes |
|
|
|
#1
|
|||
|
|||
|
pic: 6 week swerve
|
|
#2
|
|||
|
|||
|
Re: pic: 6 week swerve
Looks nice. How much pre-season testing have you done?
|
|
#3
|
|||
|
|||
|
Re: pic: 6 week swerve
If you read what it says it sounds very much like they have no experience.
|
|
#4
|
|||
|
|||
|
Re: pic: 6 week swerve
None, programmer made some swerve code for fun and I had been toying around with the idea in the offseason but everything was started fresh on everything when the season started
|
|
#5
|
|||
|
|||
|
Re: pic: 6 week swerve
Out of curiosity (if you don't mind me asking) - what was the thought process behind deciding to choose swerve for the first time in-season this year?
Spoiler for I want everyone moving this season:
|
|
#6
|
|||
|
|||
|
Re: pic: 6 week swerve
Quote:
Spoiler for more lyrics:
|
|
#7
|
|||
|
|||
|
Re: pic: 6 week swerve
![]() *Looks good Luke, we've got 4030 on our Fantasy FIRST alliance so I'm really hoping you pull it off ![]() Last edited by Navid Shafa : 21-01-2015 at 14:57. |
|
#8
|
|||
|
|||
|
Re: pic: 6 week swerve
Haha this is beautiful
Something important I forgot to mention is that we have a set day in week 4 where we will consider if we have actually made it to a point where we think our swerve gives us any benefit over a traditional tank drive. When subsystem integration is fully cadded it will include a fully fledged tank drive configuration so if we decide to ditch swerve we should be able to have a running tank a few days later. |
|
#9
|
||||
|
||||
|
Re: pic: 6 week swerve
If that bottom is a single piece, you will want to add a radius on the inner edges on the top.
How thick is the bottom plate? It looks pretty thin right now. How are you constrianing the bevel gears on that shaft? How are you constraining the other gears? Your top plates are too thin. It looks like it's 1/8" at most. Make it 1/4" to be really safe. I LOL'd at that gear on the top. I assume that's a versakey gear with 3/8" hex bore like I ised on my drill press verson. You need some thrust bearings on the module to support the vertical loads. This year more than ever it's going to be turning under a lot of load. All things considered I would not do a swerve drive fresh out of the box. Please consider buying something like a premade team 221 revolution module and just belting some motors to it. |
|
#10
|
|||
|
|||
|
Re: pic: 6 week swerve
Quote:
The bottom is being milled out of a single piece of 4x6x.25" 6061 channel the plates are .125, but this is designed to use the chassis to beef up the outer edges and the gray squares are actually bearing blocks holding 1" ID 2"OD bearings. these are bolted straight through, counterbored on the top bearing block, with nut clearance on the bottom. We think this should be fine for preventing the plates from warping. I didnt see your drill press swerve but yea it's a 3/8 bore 44 tooth versakey gear. Great minds think alike (and fools seldom differ) there is a 1" ID thrust bearing and accompanying washers in there. |
|
#11
|
||||
|
||||
|
Re: pic: 6 week swerve
Put your module into the CAD of the field right at the transition between the carpet and the scoring platform. Rotate the module as it would if the steering motor was rotating it, will that low ground clearance gear run into the ramp in any orientation? Looks to me like it will.
|
|
#12
|
|||
|
|||
|
Re: pic: 6 week swerve
Quote:
|
|
#13
|
||||
|
||||
|
Re: pic: 6 week swerve
Quote:
|
|
#14
|
|||
|
|||
|
Re: pic: 6 week swerve
Unless we want to do any sort of rotation on the step, that could cause the gear to hit the step and that would obviously be bad. The solution was to go from a 30:50 gear reduction to a 40:40 which increased the max fps from 11.5ish to 15ish but since pushing isn't an issue the lost torque from turning down wheel speed in programming shouldn't be an issue
|
|
#15
|
|||
|
|||
|
Re: pic: 6 week swerve
Like a lot of other people we thought omnidirectional drive would be useful, swerve was best for our method of dropping off stacks of totes, and we honestly just thought it would be fun.
|
![]() |
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|