BLOWN COMPONENT! In need of 2004 Robot controller to borrow for 2 days

Michael Luedtke · #1 21-02-2004, 21:17

Hi all,

Team 75 has an urgent petition to the NJ teams. We have blown robot controller and will have to order spare equipment. The earliest this will come in is Tuesday morning.

If anyone has a spare 2004 robot controller that we could use for Sunday and Monday and is in the tri-state area close to NJ- we would like to borrow it for 2 days.

I am willing to drive to pick it up, just would like to know where I can get one in hand for the next 2 days until replacements come in the overnight mail. Your ideas / advice on courses of action will be greatly appreciated and I will check this thread until Tuesday.

Thanks and Regards,
--Michael Luedtke

Michael Luedtke · #2 22-02-2004, 04:47

Hi all,

We reprogrammed the robot in p-basic. It took a bit, but we are allright until Tuesday.

Regards,
--M

Elgin Clock · #3 22-02-2004, 04:55

I'm glad things worked out for you!! That would not be a good thing. Not being able to drive the robot to do some last minute tweaking.

See you at the NJ Regional?

Hinkel Y. · #4 22-02-2004, 05:11

How did you blow your RC? Anyways, I hope you guys can get the RC in time and program C language into it... Good luck!

Michael Luedtke · #5 22-02-2004, 14:05

We must have had a random arc or fell prey to static electricity. The unit eprom does not retain the program. Everytime you boot, it never keeps the program in memory. We went through everything, and it was the robot controller itself. Thanks for your posts, and I'll see you at the NJ regionals Elgin.

It was quite a bit of work getting it to run in pbasic though. I was hoping someone had an extra we could have used in the interim.

--M

Tom Bottiglieri · #6 22-02-2004, 14:06

hold up.. you may not have a blown controller.. the same thign happened to us. What LED's are on when you boot up? Is it falling back into the program state every time you restart?

Michael Luedtke · #7 22-02-2004, 22:09

yellow on program, and green on power. Only the two are lit.

--M

Tom Bottiglieri · #8 22-02-2004, 22:14

u guys are in luck... all u need to do is read team update #9... but to save u the agony of looking i will tell u what to do.
1) Hold both the program and reset buttons.
2)Then, let go of reset
3)Wait until the power led is solid green.
4)let go of program
5) download the program
6)hit reset

You should now be set to go!

Michael Luedtke · #9 22-02-2004, 22:14

It does keep falling into the program state.

--M

Michael Luedtke · #10 22-02-2004, 22:15

Thanks!!!!

--m

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
2004 Robot Contest With 1million prize	Jimmy Holmes	General Forum	9	07-08-2002 17:38
Controlling a FIRST robot with a Lego RCX Controller?	archiver	2001	5	24-06-2002 04:19
Fingers and Robot Controller	archiver	2001	4	23-06-2002 23:54
WASH Palm scouting at the Championship	Mike Soukup	Scouting	2	19-04-2002 15:14
about how Drive Train push the robot... shouldn't the force accelerate the robot?	Ken Leung	Technical Discussion	12	26-11-2001 09:39