Who's missing parts?

[sanddrag]

Who is missing parts from their kit and what are you missing? We are missing the LED clusters, a Globe motor, a Van door motor, and maybe some small other stuff. Also, the one Van Door motor we got had a red sticker on it. On the sticker was the hand written word "Bad" That does not put confidence in me. (But overall a very nice kit).

[n0cturnalxb]

We're missing the LEDs and I have no idea what else. I wasn't there when they were doing the inventory.. hoping they did the inventory correctly, buuut I think I should be able to trust them.

[Barry Bonzack]

We are also missing the LED clusters, a globe motor, a van door motor, and something to do with pneumatics i think. We also had some discrepancy of the part numbers of the window motors, but don't think it should be a big deal. Everything else looks great and can't wait to dig in.

[Dested]

Hmmm, no light cluster here either... Our servos arent the right part number too. We are also missing a 2 window motors and im sure something else.

[J Flex 188]

You are to pick up the LED's at the regional events this year and mount them there. (questionable, but we have to accept that=)). We are also missing motors as well (the same ones i believe)

[Jeffrafa]

We are missing the same two motors, globe and van door (we have 1 of each but the inventory says 2) as well as we are unsure about only having 1 pneumatics tank and we are missing a couple little things from pneumatics (just a few fittings, not a big deal)


As j flex said, it lists the LED clusters as something you recieve AT the event, somewhat odd i thought, but not a big deal.


Mike, as far as the hall effect sensors - look carefully, we found our hall effect sensors in the bubble wrap bag with the accelerometer actually stuck to the metal housing of the accelerometer (they are very small, only about 1/4" dia. and pretty short w' 4 pins sticking out of them.)

[sanddrag]

Originally Posted by Jeffrafa

Mike, as far as the hall effect sensors - look carefully, we found our hall effect sensors in the bubble wrap bag with the accelerometer actually stuck to the metal housing of the accelerometer (they are very small, only about 1/4" dia. and pretty short w' 4 pins sticking out of them.)

That's where ours were too. It looked like part of the accerlerometer to me. Those really should have been in a separate little bog with how small they are.

Originally Posted by jgannon

Oh man... and they still put it in your kit?

Yes, and the Chiaphua motors were sitting in water. Not much water, but some components like the tetra connecters (luckily that is all) were just soaked. We were able to drip a little stream of water out of the fisher price gearboxes.

[meaubry]

Seems to be a common issue. We also were missing a globe and Van Door motor as well as some pnuematic stuff.
As far as the window motors go - the jideco is identified on the part, but the other one isn't and the part number on the side doesn't match what the bill of materials identifies it as, but I know that it is the other window lift motor because of the gear on the end is the same and it fits the plastic coupling included in the kit.
We also got another motor (looks kinda like a drill motor in a bag with 2 sensors - I think) but I don't see that motor listed on the bill of materials, any help?

[Lisa Perez]

We are missing a globe, a lead wire assembly, and a chain link.

Meaubry - maybe the mabuchi? It's in a different grouping on the list of parts.

[Eric Reed]

I think the lead wires are attached to the pilot valves.

I wasn't able to find the taigene motor on the missing parts form...although admittedly I was sleepy...anyone else see it?

Eric

Originally Posted by Lisa Perez

We are missing a globe, a lead wire assembly, and a chain link.

Meaubry - maybe the mabuchi? It's in a different grouping on the list of parts.

[Doug G]

We're missing one Tiagene van door motor, and one Master Link as well, and I think we're missing the Hall effect sensor also, but after reading this, I'll double check tomorrow that it isn't stuck on the accelerometer or something. I see the missing Taigene motor is missing from most kits, perhaps there'll be an quantity update soon, as that is a major item! Regarding the Master Link; perhaps that's why they had us get one with the Advance Materials List - I was wondering why we needed one Master Link for the field (and Lithium grease?).

[Mr. Steve]

We are also missing the two motors that everyone else is we found the hall effects stuck to the accelerator in the bubble wrap. There is a second master link inside the chain box

Just wondering did anyone get a sub base (SY3000-27-1T), if so, what is it?

[Joshua May]

I just checked back and we are missing one Globe Motor and one Van Door Motor as well.

[jgannon]

Originally Posted by Mr. Steve

There is a second master link inside the chain box

Thanks... that's one of the things we were missing.

Originally Posted by Mr. Steve

Just wondering did anyone get a sub base (SY3000-27-1T), if so, what is it?

At our kickoff, they handed them to us separate from the KOP, with the Mabuchi motor. They are white pneumatics parts... can't tell you much more than that. I'm a programmer.

[Jeffrafa]

Originally Posted by Mr. Steve

Just wondering did anyone get a sub base (SY3000-27-1T), if so, what is it?

its the manifold peice to the double solenoid valves (SY3240-5LOZ). This year these valves didn't come assembled, so you half to screw the sub base on the bottom (don't forget the seal) then screw on each of the solenoids (listed Pilot valve SY114-6LOZ)

Hope this helps