Position idlers to get better chain wrap -- a question about good practices.

[Madison]

So, I guess I'm looking for words of advice and consolation as I deal with trying to elegantly tension chain and achieve good wrap around my drive sprockets.

Assume that tensioning is achieved by moving the outer drive wheel and sprocket away from all of the others -- toward the end of the robot. The idler is attached to the frame rail and is fixed in place.

How close can I reasonably put the idler to the gearbox output sprocket (shown floating in space) to achieve increased chain wrap without it being so close that the sprockets are acting as spur gears, too.

Are there any situations that may arise from creating serpentine chain wrap, speaking generally? I've never designed such a complex chain run before; and I realize it's not even that complex.

[RyanN]

Maybe I don't understand what you are saying, but why not try this? I made it in Paint in about 10 seconds, so don't kill me...

[Madison]

Originally Posted by RyanN

Maybe I don't understand what you are saying, but why not try this? I made it in Paint in about 10 seconds, so don't kill me...

Well, I guess I'm trying to find out what sort of advice or experience folks have with such an arrangement -- which is really just an extreme case for what I have on my model. It seems to me that, as you increase chain wrap with such a setup, you correspondingly increase the chain's desire to tear the idler off its mount entirely. I'm just curious to learn what folks have found to be a happy medium or that I'm concerned for nothing.

[RyanN]

Originally Posted by M. Krass

Well, I guess I'm trying to find out what sort of advice or experience folks have with such an arrangement -- which is really just an extreme case for what I have on my model. It seems to me that, as you increase chain wrap with such a setup, you correspondingly increase the chain's desire to tear the idler off its mount entirely. I'm just curious to learn what folks have found to be a happy medium or that I'm concerned for nothing.

Well, this is true. We broke the shaft holding on our idler last year, but it was really a bad design flaw because the metal was so thin where it broke. The amount of force on the idler is a lot (I think our engineer was saying that we had over 400lbs of force on our idler) We ended up replacing our lathe built idler bolt assembly with just a plain 'ole bolt that worked for the rest of the regional.

[=Martin=Taylor=]

Originally Posted by M. Krass

I'm just curious to learn what folks have found to be a happy medium or that I'm concerned for nothing.

We used a serpentine chain-wrap system in 2006 and it was a disaster. The chains fell off, they even broke! We had a six motor drive train and so much of the power was lost to friction that we barely had any pushing power at all!

I'll never use tensioners of any kind again. Not in the drive train, on the arm, or anywhere else. Moving the axels is a far more elegant and efficient solution.

And yes, I realize hundreds of teams use tensioners just fine. Thats just my opinion.

[AdamHeard]

Originally Posted by Hachiban VIII

We used a serpentine chain-wrap system in 2006 and it was a disaster. The chains fell off, they even broke! We had a six motor drive train and so much of the power was lost to friction that we barely had any pushing power at all!

I'll never use tensioners of any kind again. Not in the drive train, on the arm, or anywhere else. Moving the axels is a far more elegant and efficient solution.

And yes, I realize hundreds of teams use tensioners just fine. Thats just my opinion.

That's weird.... we had a serpentine wrap in a six motor drive and there we no problems. Never had a chain derail, ever. We still had great pushing power as well, no more power loss than a regular setup.

[RyanN]

Originally Posted by AdamHeard

That's weird.... we had a serpentine wrap in a six motor drive and there we no problems. Never had a chain derail, ever. We still had great pushing power as well, no more power loss than a regular setup.

You won't have trouble with chain if you have the correct setup. Little sprockets save weight, but they put more tension on the chains, allowing them to snap. The constant forward and reverse of our robots makes the chains slap around, often derailing them, so use guides (we make our own nylon guides, and haven't had a chain derail since 2005. Just my advice...

[lukevanoort]

Originally Posted by AdamHeard

That's weird.... we had a serpentine wrap in a six motor drive and there we no problems. Never had a chain derail, ever. We still had great pushing power as well, no more power loss than a regular setup.

From the pictures in FIRST Robots: Behind the Design, it appears that the idlers that 100 had in 2006 consisted of cylinders of plastic (looks to be polyethylene or maybe nylon) so it isn't really a big surprise to me that it had high frictional losses. On the other hand, we have used ball bearing idler sprockets for the last two years, and they spin really easily even with a significant amount of force applied to the chain.

[AdamHeard]

Originally Posted by lukevanoort

From the pictures in FIRST Robots: Behind the Design, it appears that the idlers that 100 had in 2006 consisted of cylinders of plastic (looks to be polyethylene or maybe nylon) so it isn't really a big surprise to me that it had high frictional losses. On the other hand, we have used ball bearing idler sprockets for the last two years, and they spin really easily even with a significant amount of force applied to the chain.

oh man.... dont have my book with me, but that much wrap on plastic rod seems like a lot of friction. No wonder.

[ChrisH]

Originally Posted by AdamHeard

oh man.... dont have my book with me, but that much wrap on plastic rod seems like a lot of friction. No wonder.

Actually if they did it right there might not have been much friction at all. The trick is to install the rod in such a way as to make sure the chain is tight and then let it "wear in" a slot on the plastic rod. You migh want to pre-wear a groove in the rod to make sure the chain stays put, but it probably is not necessary. Once the tight chain wears into the rod a little bit it will go slightly slack. It will then cease to wear and the friction will be negligible.

Another approach is to not use tensioners at all. We have done this the past few years. In this case you need to be able to locate the sprocket axles precisely. You need to design the chain loop to have an integer number of links and preferably an even integer.

If there's interest I can do a white paper on how to do this.

Chris

[Dick Linn]

If you can mount the drive motor/trans assembly midway between the wheels AND have it mount such that it can be moved vertically slightly, you could use a double-row drive sprocket and two independent chains. Each chain run is shorter, which seems to reduce tensioning problems. To tension it, just loosen the drive assembly and shim it up slightly. Team 975 has done this a couple of years. Tensioning with #35 chain was rarely required, and slipping a thin washer or two between the drive mounting plate and the frame seemed to take up more slack than you'd imagine.

http://www.chiefdelphi.com/forums/at...d=119696522 0

[wilsonmw04]

http://www.chiefdelphi.com/media/photos/27587

Here's a picture of our drive last year. I think it's similar to what you are looking at doing. We had zero problems with this and it worked very well. So well in fact, that we are using a version of it this year. Hope this helps.

[deejay021]

ok so i had a quick question... with te tough boxes we recieved a sprocket that fits perfectly ont the box... however the output sprocket is at least 2x the size of the input... so... for every rotation in the tough box we get .5 on the actual wheel...for a 1st year team we are trying to get a drivable robot thatd be a decent accomplishment in out eyes... and we are working towards that but a faster driving robot would be nice...

and my second question is actually relevant to this forum... where do you get idlers... and any ideas on mounting them?

[=Martin=Taylor=]

Originally Posted by AdamHeard

That's weird.... we had a serpentine wrap in a six motor drive and there we no problems. Never had a chain derail, ever. We still had great pushing power as well, no more power loss than a regular setup.

There's a nice picture of the setup on page 45 of FIRST Robots: Behind the Designs.

[AdamHeard]

In 2007 we had an two 10 tooth sprockets stacked vertically with about 3/8" clearance between them. We had no problems with it at all. The chain was coming in about 30 degrees off horizontal from each side (30 degrees towards the side that gave it more wrap).

Hope that helps. The mentor who designed it with us was from 687 and he had build a lot chain driven robots in the past and I believe he said as long as there is room for the chain to go trough, there won't be problems.