Team 384's Electrical Board!!!

sayso_411 · #1 09-02-2008, 22:40

Alright this is Sparky's electrical board:

Hope we didn't make any team jealous!!!

Great Job by Mr. Jeff, Tri and me!!!
*the PWM's are still to be cut to custom size and put on

bobdahaxor · #2 10-02-2008, 22:42

7 victors and 4 spikes!!!! what are you powering with all of that?

popo308 · #3 10-02-2008, 22:56

Quote:

Originally Posted by bobdahaxor

7 victors and 4 spikes!!!! what are you powering with all of that?

we have 10 victors and 1 spike....

thefro526 · #4 10-02-2008, 22:59

Thats one clean electrical bored. Where did you get the nifty right angle crimp connectors?

lukevanoort · #5 10-02-2008, 23:03

7 Victors and 4 spikes isn't that bad. We have 7 Victors and 2 Spikes, and I imagine Sparky is probably just using a couple more cylinders than us. We've gone up to eight victors before, and I've seen as many as twelve used.

Zack Briggs · #6 11-02-2008, 00:01

I'm jealous. My team doesn't design around a set electronics board beforehand, we just get whatever random space is left and have to work with it

.

sayso_411 · #7 14-02-2008, 14:43

Quote:

Originally Posted by bobdahaxor

7 victors and 4 spikes!!!! what are you powering with all of that?

Keep guessing you will see at the nationals

Quote:

Originally Posted by Zack Briggs

I'm jealous. My team doesn't design around a set electronics board beforehand, we just get whatever random space is left and have to work with it

.

Yea we had the chasis and we designed around that dimensions

mizitchell · #8 14-02-2008, 16:54

There are also no wires running to the MAXI (gold colored) fuse panel for the CIMs.

Jim E · #9 14-02-2008, 17:44

All Grounds from the Victors need to run directly to the Distribution Block.

eugenebrooks · #10 14-02-2008, 21:36

Quote:

Originally Posted by Jim E

All Grounds from the Victors need to run directly to the Distribution Block.

As per recent QandA traffic, grounds from the victors are not
required to be run directly to the distribution block, but wiring all
40 amp ground returns to the distribution block, as shown
in the provided wiring diagram, is a really good idea. I have
seen a lot of fried pushons and these were operating at currents
much lower than the CIM motor draws.

Eugene

Jim E · #11 14-02-2008, 21:51

Thanks for the clarification. Thats what I meant.

Michael Coleman · #12 10-02-2008, 22:51

Very nice!

Check the wiring for the top two Victors in the second photo. It looks like the positive and negative connections are reversed.

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
The Electrical Board for Team 2177	Rachel2177	General Forum	13	26-01-2008 22:38
TEam #2531's Robot-- Chassis and Electrical Board is done!!	beemgruem	General Forum	17	24-01-2008 21:26
Name our Electrical Board!	Excelsior	Chit-Chat	17	19-01-2006 11:14
Team 384's Animation Submission	Joe Matt	3D Animation and Competition	11	27-02-2004 20:02
team 384's aniimation	Funkymunkey90	3D Animation and Competition	7	20-03-2002 19:13