Other legal compressors this year

[Rob Colatutto]

Hello all,

We've been searching for alternate compressors that both match or beat the limits of the kit compressor, and are smaller/lighter. Has anyone had any luck finding any that fit within the rules this year, other than the kit compressor?

Any findings you all may have had would be useful, as I am sure many veterans would like to run with a smaller compressor this year.

Thanks,
Rob

[scottydoh]

I was almost 100% sure any other compressor was illegal, but I stand corrected by <R75>. This is an intriguing idea, but I suspect it will be difficult to find a compressor thats much lighter than the one provided.

[Vikesrock]

Now step back forward again.

Mike, you might want to check that you are looking at the proper year's manual. That text appears to be from <R72> from 2009.

<R75> Compressed air for the pneumatic system on the ROBOT must be provided by one and only one compressor. This compressor may be either the Thomas Industries compressor from the KOP, or an equivalent compressor that does not exceed any of the KOP compressor performance specifications (specifically: 12v, 0.8cfm flow rate, 120psi continuous pressure, 120psi maximum pressure compressor). Note: if an alternative compressor is used, during inspection the team may be required to provide documentation to show compliance with the performance specifications. Compressed air shall not come from any other source. The compressor may be mounted on the ROBOT, or it may be left off the ROBOT and used to pre-charge compressed air in the storage tanks prior to bringing the ROBOT onto the FIELD. Off-board compressors must be controlled and powered by the ROBOT.

[Mike Betts]

Kevin, et al,

Mea Culpa... I was going back and forth earlier trying to figure out what had changed...

Forget I chimed in...

Mike

[sdcantrell56]

I am really liking this compressor from viair :
http://www.cheaptruckparts.com/produ...e745a968a60d18

What is the consensus on this? Do we think its legal?

[Vikesrock]

Originally Posted by sdcantrell56

I am really liking this compressor from viair :
http://www.cheaptruckparts.com/produ...e745a968a60d18

What is the consensus on this? Do we think its legal?

Unfortunately the CFM @ 0 PSI looks to be over the .8CFM specified in the manual, so I would have to say no.

A quick glance suggests all the VIAIR compressors may suffer from this "issue".

[EricH]

Originally Posted by sdcantrell56

I am really liking this compressor from viair :
http://www.cheaptruckparts.com/produ...e745a968a60d18

What is the consensus on this? Do we think its legal?

It needs to not exceed the following: 12v, 0.8cfm flow rate, 120psi continuous pressure, 120psi maximum pressure. Plus the cost, COTS, etc.

COTS: Obviously COTS from a VENDOR.
Voltage: 12V. Good.
Flow rate: 1.03cfm flow rate at 0 PSI (under a 13.8V supply) could be an issue. It's lower at higher PSIs, but still...
Continuous pressure: Not listed that I can see. Not-so-great.
Maximum pressure: 120 PSI. Good.
Cost: Under the limit.

I'd try to find a full spec sheet for that. If none is available, I'd ask the GDC directly: We found this compressor, and we are unsure if it complies with X part of <R75>. Could you give a yea or nay?

As listed, I'd have to say nay. GDC beats me, though...

[monty1540]

You all appear to be correct, the Viair compressors are all spec'd above the Thomas compressor from the kit. The Thomas datasheet for the kit compressor shows .79 cfm @ 0psi

(Kit compressor p/n 405ADC38/12 data shown on page 4 of below link)

http://www.gd-thomas.com/workareasho....aspx?id=21654

[Stephen of REX]

Here is a smaller compressor from VIAIR:

Direct Comparison:
Kit compressor
12v,
0.79cfm flow rate,
120psi continuous pressure,
120psi maximum pressure
COTS
cost: in the KOP
Weight: 4.3 lb

VIAIR 63C
12v
0.79cfm flow rate,
100psi continuous pressure,
105psi maximum pressure
COTS
cost: $35
Weight: 1.43 lb (Its a third the weight!)

If we ask the GDC, I'd ask about this one.

[RyanN]

Originally Posted by Stephen of REX

Here is a smaller compressor from VIAIR:

Direct Comparison:
Kit compressor
12v,
0.79cfm flow rate,
120psi continuous pressure,
120psi maximum pressure
COTS
cost: in the KOP
Weight: 4.3 lb

VIAIR 63C
12v
0.79cfm flow rate,
100psi continuous pressure,
105psi maximum pressure
COTS
cost: $35
Weight: 1.43 lb (Its a third the weight!)

If we ask the GDC, I'd ask about this one.

It appears that the one you listed wouldn't be able to provide enough pressure to trip the 120PSI switch, and it is also not rated for 120PSI.

[Racer26]

yes, but if you can't generate 120psi, you dont need to be rated that high.

[martin417]

Originally Posted by RyanN

It appears that the one you listed wouldn't be able to provide enough pressure to trip the 120PSI switch, and it is also not rated for 120PSI.

Neither is the KOP compressor. Its only rated for 100 PSI, max.

[sdcantrell56]

So for 1/3 of the weight and what looks like pretty similar specs this Viair compressor seems to be quite a cost effective weight saving means for teams using the compressor.

[MrForbes]

Yeah, just be sure to buy a few extras as spares...notice the duty cycle

63C Compressor Kit VIAIR
Price: $35.00 Part Number: 00063
# 12-Volt
# Duty Cycle: 20% @ 100 PSI
# Max. Working Pressure: 105 PSI
# Amp Draw: 7 Amps
# Inline Check Valve
# Dimensions: 5.00� L x 3.00� W x 5.00� H
# Net Weight: 1.43 lbs

[Racer26]

Has anyone asked Q&A about this particular compressor? I would, but I'm not my team's Q&A contact.