|
|
|
![]() |
|
|||||||
|
||||||||
![]() |
|
|
Thread Tools | Rate Thread | Display Modes |
|
|
|
#1
|
|||
|
|||
|
auto-correct device as going over hump
is it legal for a device to come out of the robot for under 2 seconds to help the robot as it tips over coming over the hump. the way we see it our robot is going to tip forward as it goes over the hump and we want to use a pnuematic to push it back as it goes over, legal or not? we can not seem to find the answer in the rules.
|
|
#2
|
|||||
|
|||||
|
Re: auto-correct device as going over hump
<G30> has the only allowed exceptions to <R16>. Keeping your robot from tipping is not one of those exceptions, although getting back upright is.
|
|
#3
|
|||||
|
|||||
|
Re: auto-correct device as going over hump
There's also a Q&A that confirms devices like anti-roll bars cannot extend past your FRAME PERIMETER.
|
|
#4
|
|||
|
|||
|
Re: auto-correct device as going over hump
the rule says as long as it is correcting itself. technically that is what it would be doing is correcting itself. the rule does not state that the robot has to be in a non moving fashion. Or it could be considered a over the hump kicking mech right? I did not see a rule that says you can only have one kicking mech. I don't know I am just thinking outloud.
|
|
#5
|
|||||
|
|||||
|
Re: auto-correct device as going over hump
I'm not sure why I bother, but read this: http://forums.usfirst.org/showthread...light=righting
|
|
#6
|
|||||
|
|||||
|
Re: auto-correct device as going over hump
Quote:
That implies that you are already down. Therefore, extending before you go down gets you a penalty and yellow card. It would also not be a kicker, because the protection in <G30-A> specifies that it's only to interact with a ball. |
|
#7
|
|||
|
|||
|
Re: auto-correct device as going over hump
you bother, because you care, thank you for your help.
![]() |
|
#8
|
|||||
|
|||||
|
Re: auto-correct device as going over hump
Zebra,
This is the answer you are looking for... <G30> ROBOT Volume During a MATCH, no part of the ROBOT shall extend outside the vertical projection of the FRAME PERIMETER, except as follows: a. BALL Interaction Volume Solely for the purposes of interacting with a BALL, MECHANISMS that are below the BUMPER may extend up to the BUMPER PERIMETER, for a period not exceeding two seconds. After returning inside the FRAMER PERIMETER, such MECHANISMS are not permitted to re-extend beyond the FRAME PERIMETER for at least two seconds. With those restrictions, I don't think you can use your mechanism to keep from tipping. |
|
#9
|
||||
|
||||
|
Re: auto-correct device as going over hump
Quote:
|
|
#10
|
|||||
|
|||||
|
Re: auto-correct device as going over hump
Did you not read the first phrase of <G30-A>?
Quote:
|
![]() |
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| 1598 Going over the top. | DRH2o | Robot Showcase | 0 | 17-02-2008 20:12 |
| Legal? Hurdling Over Overpass and Over Lane Divider | 7-11number1 | Rules/Strategy | 11 | 20-01-2008 14:58 |
| What is your team going to do with the rack after the season is over? | Ben_pharteen | General Forum | 51 | 14-04-2007 15:27 |
| Going over 6 inch step with 12 inch wheels | Joe P | Technical Discussion | 25 | 12-04-2004 11:15 |