Hex Axle- How to

[AdamHeard]

We bought our holder for $17 on amazon. Love it.

Originally Posted by compwiztobe

You can use the hex shafts from AM if those dimensions work for you, or you can machine your own. A very inexpensive ($50-$100) tool that makes this extremely easy is a hex collet holder such as this. Put your stock in a lathe collet of the correct bore and clamp the collet into this holder. The holder can be clamped into the vice on a manual mill. Then run down one side of the stock with the end mill, rotate the collet holder in the vice, and repeat until you have six identical sides.

You can also buy hex rod from various metal suppliers, but I am unaware of specifics there.

Another thing you'll want to think about is the pieces that go on the shaft. Many you can get with a hex bore, but if you ever need to do it yourself, you will need a hex broach, or a sponsoring machine shop with one, since they are significantly more expensive (~$800 for rotary).

[Aren Siekmeier]

Originally Posted by AdamHeard

We bought our holder for $17 on amazon. Love it.

Wow, that's awesome.

[Cory]

Originally Posted by AdamHeard

We bought our holder for $17 on amazon. Love it.

As a side note to this, in my experience Fastenal has the absolute worst prices on anything metalworking related.

[Aren Siekmeier]

Haha, ok, good to know. I hadn't really done much research on the best prices, mostly just how to find them and to be able to show what they are. We'll definitely stay away from them then.

Also (to the OP), this thread has more about where to buy hex shafts and hex stock.

[Chris is me]

You can get a 1/2 hex broach for just over $100. We bought one and a 3/8ths broach and it's one of our more useful investments. Certainly not the most vital, but it's good that we have it.

We have just bought hex stock from McMaster or other cheaper sources rather than machining our own shafting with no problems. We don't step hex, but we never have found a time when that's been necessary thanks to AndyMark hex bearings.

All you should need to run a hex based anything are snap rings for retention and the occasional spacers. No keys or awkward retaining rings to get lost.

[Aren Siekmeier]

Originally Posted by Chris is me

You can get a 1/2 hex broach for just over $100. We bought one and a 3/8ths broach and it's one of our more useful investments. Certainly not the most vital, but it's good that we have it.

Are these rotary broaches? If not, have you been in many situations where you wish you had one?

[Chris is me]

Originally Posted by compwiztobe

Are these rotary broaches? If not, have you been in many situations where you wish you had one?

No and no. I don't see what we'd need a rotary broach for?

[Aren Siekmeier]

Originally Posted by Chris is me

No and no. I don't see what we'd need a rotary broach for?

I guess I was under the impression a rotary broach gave you more options (which it still does: not cutting all the way through, using it on more standard machines...), but on reading more about it it looks like they're actually worse in some cases. It all works out since it sounds like normal ones are cheaper...

[AdamHeard]

Originally Posted by compwiztobe

I guess I was under the impression a rotary broach gave you more options (which it still does: not cutting all the way through, using it on more standard machines...), but on reading more about it it looks like they're actually worse in some cases. It all works out since it sounds like normal ones are cheaper...

Blind broaching isn't terribly useful for what we do, you'd need to retain the part axially in some other operation.

We have a full set of push broaches, and use them for hundreds of holes a year without issue.

For frc, I see the only real advantage of rotary broaches being the ability to run them on a cnc mill for the teams that have an in house machine.

[AustinSchuh]

I got a chance to use a 5C hex collet at school, and it was very nice. I would highly recommend one.

[nick_sheets]

http://www.amazon.com/5C-Collet-Bloc...&n=228013&s=hi

We seem to have 5C collet at our small school shop and we seem to have the set linked above. How do you use this on the mill or lathe? We have a very very very small shop with 1 mill and a lathe. So this would be very handy!!!!!

What is the tool to the right of the picture?

Thank you!

[Karibou]

Originally Posted by nick_sheets

http://www.amazon.com/5C-Collet-Bloc...&n=228013&s=hi

We seem to have 5C collet at our small school shop and we seem to have the set linked above. How do you use this on the mill or lathe? We have a very very very small shop with 1 mill and a lathe. So this would be very handy!!!!!

What is the tool to the right of the picture?

Thank you!

I've never seen them before, but it looks like those would be used on the mill:
http://bbs.homeshopmachinist.net/showthread.php?t=36517
(There's a nice picture there that should make a lot of sense if you've had any machining experience)
I don't know for sure, and maybe someone who actually has used these before can give a more educated answer, but my best guess would be that you slide the collet inside the block, insert the piece of hex shaft, and then use the closer ring on the back to tighten the collet around the metal in addition to keeping it from sliding out of the block while in use.*

*again, best guess. If someone knows for sure how to use these, please correct me, because I'm curious as well.

[Chris is me]

You install a collet on a lathe or mill to secure parts, as opposed to something like a three jaw chuck. The cone shape of the collet squeezes the work piece in place as it is tightened into the lathe or mill.

I'd think a hex collet would probably be used on a lathe. Can't see much utility in replacing your mill's tooling with a spinning hex shaft.

[Andrew Schreiber]

Originally Posted by compwiztobe

(which it still does: not cutting all the way through, using it on more standard machines...)

Specifically the standard machines part... Could you elaborate on that? Personally, every shop I've ever worked in had an arbor press in house and that is how we always broached. Is this not standard equipment for most teams?

[JesseK]

Originally Posted by Andrew Schreiber

Specifically the standard machines part... Could you elaborate on that? Personally, every shop I've ever worked in had an arbor press in house and that is how we always broached. Is this not standard equipment for most teams?

Eh, there's no "recommended big tools for your shop" section anywhere in a manual or update (etc) from FIRST. So I doubt it's 'standard' unless there's a mentor or sponsor who knows what they're doing.