WestCoast Products: Launch

When do you think you'll have pictures?

Also, will this (http://wcproducts.net/wcp-00004/) work in a CIMple Box gearbox? It says it works for tough boxes, but doesn't mention CIMple Boxes.

It would solve all of our problems if it could.

[James Tonthat]

Originally Posted by SuperNerd256

When do you think you'll have pictures?

Right now, the gears are off being shaped, we'll have a picture of them up by Thursday. After we get them on Thursday, we'll be sending them off for hard anodizing (Type III) with Teflon coating on them. If you want to learn a bit more about them, there's some info found here.

Here's a little teaser of them in blank form.

Originally Posted by SuperNerd256

Also, will this (http://wcproducts.net/wcp-00004/) work in a CIMple Box gearbox? It says it works for tough boxes, but doesn't mention CIMple Boxes.

It would solve all of our problems if it could.

The pinion gear you posted is a direct replacement of AndyMark's 14 tooth pinion. The CIMple Box uses a 12 tooth pinion. You might be getting it confused with the 56 tooth gear which will net you greater weight savings.

I'm trying to replace the pinion gear that goes into the gearbox. I want to use the 14 tooth pinion gear instead of the 12 tooth that you're supposed to use. Does that work that way, or will it not work?

[James Tonthat]

Originally Posted by SuperNerd256

I'm trying to replace the pinion gear that goes into the gearbox. I want to use the 14 tooth pinion gear instead of the 12 tooth that you're supposed to use. Does that work that way, or will it not work?

Unfortunately, because they are different sizes, you cannot fit a 14 tooth pinion into that space and have a good mesh. A solution would be to make custom gearbox plates.


Cheers,

Originally Posted by James Tonthat

Either of these gears from AndyMark will work as a replacement pinion gear. 12x520 CIM Gear (am-0741) or CIM Gear, 12 tooth (am-0018). Although, the first one is the recommended replacement.


Cheers,

Thanks a bunch for your help, but I may not be being clear (I have a bad habit of doing so).

The ones you linked to in the post up there ^ were to 12 tooth pinion gears, the ones normally used to go on CIM motors into CIMple boxes. I want to use the 14 tooth pinion gear normally used on the toughbox to go on the CIM motor and into the CIMple Box, and I have no idea if that will work or not.

[James Tonthat]

Originally Posted by SuperNerd256

Thanks a bunch for your help, but I may not be being clear (I have a bad habit of doing so).

The ones you linked to in the post up there ^ were to 12 tooth pinion gears, the ones normally used to go on CIM motors into CIMple boxes. I want to use the 14 tooth pinion gear normally used on the toughbox to go on the CIM motor and into the CIMple Box, and I have no idea if that will work or not.

Send me an email at the email address in my signature or a private message.

Thanks.

[Feroz1325]

Rubber seals on all the bearings? Your getting ready for the water game too!!

[Cory]

Originally Posted by SuperNerd256

Thanks a bunch for your help, but I may not be being clear (I have a bad habit of doing so).

The ones you linked to in the post up there ^ were to 12 tooth pinion gears, the ones normally used to go on CIM motors into CIMple boxes. I want to use the 14 tooth pinion gear normally used on the toughbox to go on the CIM motor and into the CIMple Box, and I have no idea if that will work or not.

I think you may have a fundamental misunderstanding of how gears work.

If you have a gear set with two gears that have a given number of teeth each and you wish to replace one of them, you must come up with two new gears where the sum of the tooth counts of the two new gears are equal to the sum of the tooth counts of the first two gears. Otherwise you will end up with the wrong center to center distance and they will not mesh.

[Eugene Fang]

Congrats, RC!

604 will be using a lot of WCP parts this year. ;-)

[Jacob Paikoff]

I know that the gears wont ship till week two, do we have to wait to that time to order them or will they available for order earlier than that?

Originally Posted by Cory

I think you may have a fundamental misunderstanding of how gears work.

If you have a gear set with two gears that have a given number of teeth each and you wish to replace one of them, you must come up with two new gears where the sum of the tooth counts of the two new gears are equal to the sum of the tooth counts of the first two gears. Otherwise you will end up with the wrong center to center distance and they will not mesh.

Oh. That makes sense. Thanks for telling me! Good luck this year! We can't wait for SVR!

[Akash Rastogi]

Originally Posted by SuperNerd256

When do you think you'll have pictures?

WestCoast Products has provided CAD files of all products on their page here. If you need to see how they look, download the CAD file for now.