Chiaphua Spec Sheet

Joe Johnson · #1 08-01-2002, 16:49

I suppose that 3 days is enough time to wait for FIRST to upload the spec sheet for the Chiaphua Motors.

I got this directly from Chiaphua (knowing motor manufacturer's by name is worth something ;-)

Hope this helps.

Joe J.

Anton Abaya · #2 08-01-2002, 16:54

/me bows to the god.

Katie Reynolds · #3 08-01-2002, 17:31

THANK YOU!!!

- Katie

Larry Barello · #4 08-01-2002, 22:10

Something seems wrong with the spreadsheet: it claims 300 oz-inch torque from the motor at stall.

Doesn't that seem just a tad high, like 10 or 20x ?Team #492

Joe Johnson · #5 08-01-2002, 22:37

I think is it right.

Joe Ross · #6 08-01-2002, 22:53

Quote:

Originally posted by Larry Barello
Something seems wrong with the spreadsheet: it claims 300 oz-inch torque from the motor at stall.

Doesn't that seem just a tad high, like 10 or 20x

remember that the stall torque is given in oz-in and not foot pounds or newton meters like the other motors.

Larry Barello · #7 08-01-2002, 23:13

That would explain the 10-20x error .... ;^)

Marc P. · #8 09-01-2002, 06:25

Quote:

Originally posted by Larry Barello
Something seems wrong with the spreadsheet: it claims 300 oz-inch torque from the motor at stall.

Doesn't that seem just a tad high, like 10 or 20x ?Team #492

When converted to the 315 oz-in of stall torque would be 2.23 nM, using 1Nm = 141.5 oz.in.

EStokely · #9 09-01-2002, 12:59

Everyone is ahead of me.
I also thought that seemed high and went here to post the same question that Larry did, only to find out I can't read!
oz-inches are not foot -pounds
Thanks all
And a HUGE thanks to Joe!!!!!

Eric

Frank(Aflak) · #10 08-01-2003, 19:09

bah, I can't find any other specs, can I get some linkage?

like for the other motors. . . i found them the other day, but couldn't find them again . . . .

sanddrag · #11 08-01-2003, 19:16

Quote:

Originally posted by Frank(Aflak)
bah, I can't find any other specs, can I get some linkage?

like for the other motors. . . i found them the other day, but couldn't find them again . . . .

This is for the motors for LAST YEAR and the Van Door from 2001.
www.team696.org/motorspecs.html

Marc P. · #12 08-01-2003, 22:45

wow... old thread heh

Brandon Martus · #13 09-01-2003, 16:01

Note; this thread is from last season.

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Training: Interpreting Motor Spec Sheets presentation wanted	kmcclary	Motors	3	11-11-2003 17:26
Matching Drill and Chiaphua	sanddrag	Motors	12	17-01-2003 11:23
Coupling the Chiaphua & a variable Drill output	Jeff Sharpe	Motors	9	13-01-2003 20:21
sheet rubber	Adams High Man	OCCRA	1	20-10-2002 10:07
Chiaphua gearing (Chippy and Bosch)	honky	Motors	3	31-01-2002 10:28