Go to Post please....Mr. Needel is my father :rolleyes: - Greg Needel [more]
Home
Go Back   Chief Delphi > Technical > Programming
CD-Media   CD-Spy  
portal register members calendar search Today's Posts Mark Forums Read FAQ rules

 
Closed Thread
Thread Tools Rate Thread Display Modes
  #1   Spotlight this post!  
Unread 08-02-2003, 20:48
MikeDubreuil's Avatar
MikeDubreuil MikeDubreuil is offline
Carpe diem
FRC #0125 (Nu-Trons)
Team Role: Engineer
 
Join Date: Jan 2003
Rookie Year: 1999
Location: Boston, MA
Posts: 967
MikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond repute
Send a message via AIM to MikeDubreuil
Programming Port I/O

Our team has been trying to tap into the programming port. However, every attempt has been marked with a Basic Run Error. We can't even get Serout to talk to Hyper Terminal.

Programs will run until you try to "call" from Hyperterminal. Then the RC will experience a Basic Run Error. Does anyone have any positive experience with serial communication over the program port?
  #2   Spotlight this post!  
Unread 08-02-2003, 21:07
rbayer's Avatar Unsung FIRST Hero
rbayer rbayer is offline
Blood, Sweat, and Code
no team (Teamless Orphan)
 
Join Date: Mar 2002
Rookie Year: 2001
Location: Minnetonka, MN
Posts: 1,087
rbayer is a glorious beacon of lightrbayer is a glorious beacon of lightrbayer is a glorious beacon of lightrbayer is a glorious beacon of lightrbayer is a glorious beacon of light
Send a message via AIM to rbayer
You cannot use Hyperterminal as it sets the DTR line to high. This makes the Stamp think you are trying to program it and causes it to reset. For now, you're going to have to find a different program to view it with, or wait a few days and I'll see if I can throw together a quick serial port viewer.

--Rob
__________________
New C-based RoboEmu2 (code simulator) available at: http://www.robbayer.com/software.php
  #3   Spotlight this post!  
Unread 09-02-2003, 13:59
MikeDubreuil's Avatar
MikeDubreuil MikeDubreuil is offline
Carpe diem
FRC #0125 (Nu-Trons)
Team Role: Engineer
 
Join Date: Jan 2003
Rookie Year: 1999
Location: Boston, MA
Posts: 967
MikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond reputeMikeDubreuil has a reputation beyond repute
Send a message via AIM to MikeDubreuil
I have used Hyperterminal before. Approximately 3 years ago with a Stamp BS2 and a development board. My Stamp book has information on connecting the Stamp to Hyperterminal. Unfortunately, that book is 100 miles away from me right now.
  #4   Spotlight this post!  
Unread 09-02-2003, 18:25
Ryan Meador Ryan Meador is offline
Registered User
#0190
Team Role: Electrical
 
Join Date: Jan 2002
Rookie Year: 1999
Location: Worcester, NH
Posts: 68
Ryan Meador will become famous soon enough
You could build your own serial cable with all the pins disconnected except for the 2 needed for tx/rx. You could also write your own computer program that would read from the port (like 40 lines of C++, almost all of which is setting port options)
__________________
-Ryan

"You're not a real programmer until you end all your sentences with semicolons;"
  #5   Spotlight this post!  
Unread 10-02-2003, 17:07
mjosephi mjosephi is offline
Registered User
#0159
 
Join Date: Jan 2003
Location: Fort Collins, CO
Posts: 3
mjosephi is an unknown quantity at this point
When you launch hyperterminal set Flow Control to None and that should allow you to communicate with the BS.
Closed Thread


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Fried program slots? Jeff Waegelin Programming 18 19-03-2003 18:08
Horror Story - Laptop com port again Lloyd Burns Programming 3 17-03-2003 07:33
Dashreader.dll: A Visual Basic .NET user control to read the dashboard port Ameya Programming 4 12-01-2003 23:40
Change to Initializing Inputs and Outputs Jferrante Programming 4 07-01-2003 11:36
Programming Port GreenDice Programming 12 10-01-2002 09:14


All times are GMT -5. The time now is 04:00.

The Chief Delphi Forums are sponsored by Innovation First International, Inc.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi