|
|
|
![]() |
|
|||||||
|
||||||||
![]() |
| Thread Tools | Rate Thread | Display Modes |
|
#1
|
|||||
|
|||||
|
Multi-turn pots?
I am looking for a 2 - 5 turn potentiometer. The style that has a shaft. Any help would be appreciated.
- Mike |
|
#2
|
|||
|
|||
|
We have tons of pots in a box in our shop. Im going there tomorrow for a competition readiness meeting, and Ill take a look for you to see if we have any.
|
|
#3
|
|||||
|
|||||
|
Thanks a lot...
The pot is for our claw. We need more than a single turn. The only thing I can find in Digi-Key is a 10 turn. The device only rotates about 300 degrees which would kill our resolution. |
|
#4
|
||||
|
||||
|
http://www.chiefdelphi.com/forums/sh...threadid=16944
Digikey does carry other multi-turn pots. Look under Potentiometers - Wirewound. There are a few 300 degree potentiometers. You cannot use that one, though, because they only come in 25K Ohms. You need 100K Ohms. Search around the entire catalog and see if you can find another 300 or so degree pot. The other option is to take a standard pot and stick a gear on it. *edit* The second item on that link, 1/8Watt Carbon pot, is a 300 degree pot and comes in 100K Ohms. However, the wattage might be a bit too low (you'll find your pots burning up). The manual states 50mA max, which means you'd need 5*.05 = 1/4 Watt potentiometer. Last edited by Jnadke : 02-03-2003 at 12:58. |
|
#5
|
|||||
|
|||||
|
Quote:
I saw that one too. I don't mind going higher in resistance because I can just throw a resistor across it. Lower won't really help. |
|
#6
|
||||
|
||||
|
There are some 300 degree pots listed under "Stock-pot" but again they are only rated for 1/3 Watt.
|
|
#7
|
|||
|
|||
|
If you get a 100K pot, you are not limited to digikey or future.
The supplier that I like for things like this is mouser electronics (www.mouser.com). They have good selection, quick shipment, and no minimum order. Although, a quick look through their catalog did not disclose exactly the option you wanted. Another approach might be to get a Grayhill gray-scale mechanical encoder from Digi-key. This can be connected to four digital inputs (16 bits per revolution resolution or one nibble), and gives you unlimited rotation. I don't know how fine a positioning you need to do. Of course, you could gear this and accumulate your value in software to improve your resolution. I would definitely recommend against using a 300 degree (maximum) pot for 300 degree rotation. Your accuracy is very poor at the ends of the travel and if you do not position the pot exactly, you will break it quickly. We normally use the 270 degree rotation pots for about 200 degrees of rotation. |
|
#8
|
|||||
|
|||||
|
We have the grayhill Encoder, we bought the 32 position though. Our device moves too fast for the serin to pick up every pulse.
|
|
#9
|
|||||
|
|||||
|
You might try gearing the pot to the device you are trying to measure. That makes the pot an off the shelf item. The shaft of most pots are 1/4" so finding gears that mate with that shaft is pretty easy. Plastic or nylon gears are available from our list of suppliers cheap and they work well. You get to use maximum resolution from the pot without sacrifice. Just be sure to give yourself a little leeway. Pots are about 270 degrees but that is not guaranteed. Plan for no more than 250 and you should be fine.
|
|
#10
|
|||
|
|||
|
Quote:
|
|
#11
|
|||||
|
|||||
|
Quote:
Quote:
|
|
#12
|
|||
|
|||
|
Do you suffer from the "we.ve finished building the robot, so let's add controls" syndrome ?
We have arms that rotate about 225 degrees, but they are mounted on a gear, so gearing it was easy. Unfortunately, the smallest meshing gear had too many teeth to allow more than about 4 turns of the ten-turn pot. Works ok though. Al is right about leaving some leeway, though. When adjusting your system, there is nothing nicer than not having a motor drive the arm past the end of the pot's rotation, so the pot doesn't need emergancy replacement. ![]() |
|
#13
|
|||
|
|||
|
Quote:
|
|
#14
|
|||
|
|||
|
You plan before you build ?!?!?!?!?
Sounds like something an engineer would do ! Radical ! ![]() |
|
#15
|
|||||
|
|||||
|
Quote:
|
![]() |
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Multi Drive Fun... | Sachiel7 | Technical Discussion | 14 | 13-10-2003 01:06 |
| College Advisor turn outs | Guyute | General Forum | 4 | 20-06-2003 13:35 |
| 10 turn 100k pots | rust710 | Electrical | 5 | 02-04-2003 15:10 |
| multi rotational potentiometers | jdawson | Electrical | 8 | 27-01-2003 08:12 |
| 3-turn pots | archiver | 2001 | 2 | 24-06-2002 01:24 |