|
|
|
 With CD down... I wasn't sure what to do with my free time. I almost had a reality check and thought I might go outside. - Barry Bonzack [more] |
 |
|
|||||||
|
||||||||
 |
| Thread Tools | Rate Thread | Display Modes |
|
|
|
| With CD down... I wasn't sure what to do with my free time. I almost had a reality check and thought I might go outside. - Barry Bonzack [more] |
|
|
|||||||
|
||||||||
|
| Thread Tools | Rate Thread | Display Modes |
|
#1
|
||||
|
||||
|
roboRIO Driver Issue
My team and I were trying to image the new roboRio so we can test the controls.
However, the computer is not recognizing the USB, and so the roboRIO imaging service through LabVIEW does not work. We have uninstalled and reinstalled LabVIEW many times, including the updates through the "NI Update Service". I suspect it is an issue with the driver not recognizing the roboRIO. Has anyone else had this problem? Last edited by JMankewitz : 05-01-2015 at 19:58. 
|
|
#2
05-01-2015, 19:53
|
||||
|
||||
|
Re: roboRIO Driver Issue
Did you install the LabVIEW DVD or the FRC Update Suite?
|
|
#3
05-01-2015, 20:02
|
||||
|
||||
|
Re: roboRIO Driver Issue
We did the CD and the FRC Update Suite, then the NI Update Service.
|
|
#5
05-01-2015, 20:06
|
||||
|
||||
|
Re: roboRIO Driver Issue
Correct, USB not Ethernet.
|
|
#7
05-01-2015, 22:01
|
||||
|
||||
|
Re: roboRIO Driver Issue
We're going to do more troubleshooting tomorrow, but from what I remember, the computer recognizes that something is plugged into the USB port on the computer, but it does not have the drivers to support the roboRIO.
I don't know about the USB Ethernet driver, but I can update when I get back to school tomorrow.
|
|
#8
05-01-2015, 23:01
|
||||
|
||||
|
Re: roboRIO Driver Issue
Update: Windows does not recognize the USB ethernet driver.
|
|
#9
05-01-2015, 23:23
|
|||
|
|||
|
Re: roboRIO Driver Issue
The FRC update for your computer (the one that contains the driver station and the gamepad install) should also have your drivers for your RoboRIO, if not I would recommend going into device manager and manually specifying the driver, that should allow you to communicate with it like normal.
|
|
#10
05-01-2015, 23:35
|
||||
|
||||
|
Re: roboRIO Driver Issue
Thanks! We gave that a try today, but we weren't sure where the driver was. Do you know the directory of the correct driver? Thank you so much !
Last edited by JMankewitz : 05-01-2015 at 23:38.
|
|
#11
05-01-2015, 23:45
|
||||
|
||||
|
Re: roboRIO Driver Issue
The only drivers I can find are for PXI C:\Program Files (x86)\National Instruments\PXI\Drivers is PXI used for the roboRIO?
|
|
#12
06-01-2015, 07:43
|
|||
|
|||
|
Re: roboRIO Driver Issue
If you don't figure it out pretty quickly, please contact NI support. Start at ni.com/frc.
Greg McKaskle
|
|
#13
06-01-2015, 12:52
|
||||
|
||||
|
Re: roboRIO Driver Issue
The roboRIO USB Driver is at...
C:\Program Files (x86)\National Instruments\CompactRIO\Staging\USBLAN ... but if it didn't auto-register you might have other problems, Greg's suggestion is probably best.
|
|
#14
06-01-2015, 14:07
|
||||
|
||||
|
Re: roboRIO Driver Issue
Okay, we figured it out!
Here is what we did in case anyone else has this problem: 1) Followed these directions for installing labVIEW completely: https://wpilib.screenstepslive.com/s...5-labview-only 2) Following the instructions for the update suite completely: https://wpilib.screenstepslive.com/s...-all-languages 3) Download all NI Updates (one at a time and restart after each) 4) We also used a different USB A -> B cable to connect to computer The computer finally recognized the roboRIO, so we'll configure it today! Thank you all very much for the help, we really appreciate it. Good luck!
|
|
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|
Linear Mode
