PIDs out of control

[awallace3160]

(OP on a fellow programmers computer here)

We are using 5-turn potentiometers and they are only intended to rotate 180 degrees maximum. We try to make sure that the pots are set to rotate near the middle of each ones range so as to avoid over rotating them if they go a little bit beyond the desired setpoint.

We are using the PotentiometerGetNormalized.vi to get our values, which return as a percentage of the total voltage, we have found. So, we are trying to return 3-4 decimal accuracy on each potentiometer.

So, I'm not sure if our program trying to reach this accuracy is hitting the pots' "blind spot" or not, because I'm not absolutely sure what that means.

[Ether]

Originally Posted by awallace3160

We are using 5-turn potentiometers and they are only intended to rotate 180 degrees maximum.

It's not clear what you mean. It could be interpreted at least 2 different ways:

1) The wheel is currently at 179 degrees and it is being commanded to go to -179 degrees. The controller will rotate the wheel 358 degrees counterclockwise to get to the commanded angle, because the controller does not want to exceed 180 degrees.

or

2) The wheel is currently at 179 degrees and it is being commanded to go to -179 degrees. The controller will rotate the wheel 2 degrees clockwise to get to the commanded angle, because that is less than 180 degrees movement.

Which of the above descriptions is what you intended? (or something else?)

We try to make sure that the pots are set to rotate near the middle of each ones range so as to avoid over rotating them if they go a little bit beyond the desired setpoint.

When you process the signal from the pot, do you let the signal go beyond 180 degrees? Or do you constrain it to be in the range +/-180 before using it? In other words, say the pot is at zero degrees, and then gets moved 181 degrees clockwise. Will your processed pot reading be +181 degrees or -179?

We are using the PotentiometerGetNormalized.vi to get our values

I don't know what that means, but it sounds like it is converting the pot reading to +/-180 degrees. If such is the case, depending on your code that could make the controller go nuts. I suggest you post your code for review.

So,I'm not sure if our program trying to reach this accuracy is hitting the pots' "blind spot" or not, because I'm not absolutely sure what that means.

If you've got a 5-turn pot and you are centering it and avoiding over-rotating, there should be no blind spot (a dead area where there's no usable signal).

[wildaburk3160]

From what we've gathered, the PotentiometerGetNormalized.vi gets the voltage reading from the potentiometer and returns it as some sort of proportion of the total possible voltage. It seems that 90 degrees ~ .1 change in the returned value.

So, if we were to set our "midpoint" at the middle of the pots rotational range, we would set our setpoint to .50. Our goal then is to rotate at maximum 90 degrees in either direction from this point. Theoretically, this should change the value by .1, but it has a small variation, so we have it set to where we manually control the "maximum" and "minimum" values of the pot.

None of these values we have set come up near the extreme values of rotation, which would either be "0" or "1".

We haven't thrown in any limitations to rotations in the program other than how far we can change the setpoint, but I will soon implement something.

[Ether]

Originally Posted by wildaburk3160

the PotentiometerGetNormalized.vi gets the voltage reading from the potentiometer and returns it as some sort of proportion of the total possible voltage

As I said, I am not familiar with PotentiometerGetNormalized... but for a 5-turn pot, 1/4 of a turn (90 degrees) would be (1/4)/5 = 0.05 of the total range.

[wildaburk3160]

Well, regardless of it's particular function, do you have any other ideas as to why this problem is occuring?

[Ether]

Originally Posted by wildaburk3160

Well, regardless of it's particular function, do you have any other ideas as to why this problem is occuring?

It's either hardware or software. Here's a good way to find out if it's software:

Originally Posted by Ether

I suggest you post your code for review.

[GeeTwo]

Originally Posted by Ether

It's either hardware or software. Here's a good way to find out if it's software:

And to help figure out if it's hardware, it would help if we understood just what hardware you're using, how it's connected, and how it's supposed to work. Including links to spec sheets would also be helpful!