Whats the big deal with in tube gearing?

[cadandcookies]

Originally Posted by Dunngeon

It's possible, but you'd have to use 2x2 tubing to get both of the belts to fit into the interior. From what I've read on Delphi, chain in tube is better than belt since chains (rarely) snap and don't stretch over time, eliminating the need for a tensioning system.

While chains do not stretch over time like belts do, they do wear over time, which has a very similar effect. For the most part in my experience neither phenomenon is typically noticeable in a robot during a standard (1-2) event season, but both can be observed on a practice robot with sufficient hours of use. In a high-use demobot, both have a potential to give you issues if you use it long enough.

Both chain in tube and belt in tube have been done successfully in competition-- 1625's Lobster Drive and of course 118's chain in tube come to mind as examples of belt and chain respectively.

[Cash4587]

I could be wrong, but I am pretty certain chain definitely does stretch over time, more so than belts. Due to the fact roller chain has metal pins and bushings that all see general wear and tear, I think chain elongates the more use it sees.

[Ty Tremblay]

319 hasn't made a chain-in-tube drivetrain yet, but what I find attractive about the design is it's simplicity and the volume savings. It may be a little less easy to work on, but due to the protected nature of the chain, the odds of you having to work on it are smaller. Mounting gearboxes becomes much easier as well.

Originally Posted by Cash4587

I could be wrong, but I am pretty certain chain definitely does stretch over time, more so than belts. Due to the fact roller chain has metal pins and bushings that all see general wear and tear, I think chain elongates the more use it sees.

Under the forces it'll see in FRC, chain cannot stretch. It can wear, however.

[Lil' Lavery]

Originally Posted by Mike Marandola

The main advantage is that it saves space. This year, some robots needed the extra space for the totes to fit inside their chassis. It also opens up more options structure wise. For example, this large cross member on 254's robot wouldn't be possible with a traditional WCD. Other benefits are chain protection and aesthetics. Of course it would be up to your team to decide if the extra space is worth the challenge.

That large cross member would be possible with exterior chain/belt, you'd simply have to route the chain around it*.

*Which obviously comes at the price of additional chain and idlers.

[Dunngeon]

Originally Posted by cadandcookies

While chains do not stretch over time like belts do, they do wear over time, which has a very similar effect. For the most part in my experience neither phenomenon is typically noticeable in a robot during a standard (1-2) event season, but both can be observed on a practice robot with sufficient hours of use. In a high-use demobot, both have a potential to give you issues if you use it long enough.

Both chain in tube and belt in tube have been done successfully in competition-- 1625's Lobster Drive and of course 118's chain in tube come to mind as examples of belt and chain respectively.

I'm more concerned about the chance of snapping a drive belt, rather than the wear. It's nearly impossible to snap chain in FRC if assembled correctly, from my (limited) experience it's quite a bit easier with belts.

[Joey Milia]

Originally Posted by Dunngeon

I'm more concerned about the chance of snapping a drive belt, rather than the wear. It's nearly impossible to snap chain in FRC if assembled correctly, from my (limited) experience it's quite a bit easier with belts.

15mm wide GT2 belt is pretty much indestructible for FRC purposes.

EDIT: 5mm pitch for clarification

[Dunngeon]

Originally Posted by Joey Milia

15mm wide GT2 belt is pretty much indestructible for FRC purposes.

Good to know

[cadandcookies]

Originally Posted by Dunngeon

I'm more concerned about the chance of snapping a drive belt, rather than the wear. It's nearly impossible to snap chain in FRC if assembled correctly, from my (limited) experience it's quite a bit easier with belts.

I see. I'd second Joey-- 15mm GT2 or HTD belt is in my experience on the same level as chain in terms of breaking. In my experience if you can get to 36t pulleys, 9mm HTD or GT2 is also pretty hard to break (as in, I've never had an issue with it).

[Dunngeon]

Originally Posted by cadandcookies

I see. I'd second Joey-- 15mm GT2 or HTD belt is in my experience on the same level as chain in terms of breaking. In my experience if you can get to 36t pulleys, 9mm HTD or GT2 is also pretty hard to break (as in, I've never had an issue with it).

It wouldn't surprise me if the teams I've seen snap belts were using 9mm belts incorrectly, some teams in the PNW have a bit of a history making odd decisions.

[bobcroucher]

Chain definitely stretches through wear, mostly the pins. Park Tools sells a chain stretch gauge for bike shops. The poor man's way is to measure 24 links at 0.5 inches each totals 12 inches when new. Once the chain reaches 12.25", it's time to buy a new chain. The stretched chain will wear out the aluminum chain rings and the rear cassette, and each costs more than a new chain. A new chain lasts 1000 - 2000 miles depending on cleanliness and lubrication.

Bike wheels are obviously much larger, so the chain life will be reduced accordingly. If we scaled 1500 miles down by 4 / 27, since 4 inches is a typical WCD wheel size, and 27 inches is a typical road bike diameter, you would get about 225 miles. That's still around 11,000 round trips down and back on the 52' field. The chain is quite unlikely to wear out based on revolutions alone. Work done to move each vehicle's mass is at least within a factor of 2, and would benefit the robot.

Robots don't get much road grime, and carpet fuzz isn't very abrasive, but they usually don't get much lubricant. The more lube you use, the more stuff sticks to the chain. By putting the chain in the tube, you can probably lubricate it a bit better without fear of contamination. I'm sure chains will typically last an entire season regardless. Putting the chain inside the frame tube probably helps protect it from game pieces and other robots as well.

According to Gates, a belt's stretch is nearly un-measurable over the lifetime of the belt.