Go to Post The best [fundraiser] that we did was our various little things this year, such as calanders and other things. The worst is not doing one at all. - Joe Matt [more]
Home
Go Back   Chief Delphi > Technical > Technical Discussion
CD-Media   CD-Spy  
portal register members calendar search Today's Posts Mark Forums Read FAQ rules

 
 
 
Thread Tools Rate Thread Display Modes
Prev Previous Post   Next Post Next
  #11   Spotlight this post!  
Unread 04-01-2016, 00:41
BoilerMentor BoilerMentor is offline
Registered User
FRC #1747
Team Role: Mentor
 
Join Date: Jan 2011
Rookie Year: 2006
Location: West Lafayette, IN
Posts: 130
BoilerMentor has a reputation beyond reputeBoilerMentor has a reputation beyond reputeBoilerMentor has a reputation beyond reputeBoilerMentor has a reputation beyond reputeBoilerMentor has a reputation beyond reputeBoilerMentor has a reputation beyond reputeBoilerMentor has a reputation beyond reputeBoilerMentor has a reputation beyond reputeBoilerMentor has a reputation beyond reputeBoilerMentor has a reputation beyond reputeBoilerMentor has a reputation beyond repute
Re: Sonic Shifter - recent feedback?

Quote:
Originally Posted by cbale2000 View Post
What lubricant were you using and what was the overall reductions in your drive system (including wheel size)?

IMO our 2014 robot put it's 3 CIM Ball shifters through far more abuse than the average team and the gears still look as good as new. For that matter, I've yet to see so much as a chipped tooth on any of the over 75 various Vex Pro gears we've used on competition robots in the past two years.
Gear ratios were 18.75:1 and 7.08:1. Gearboxes were lubricated with moly grease containing Teflon. The gearbox direct drove a 6" x 2" wheel at the center of the robot which was chained to the other two wheel in the drive train side, also 6" x 2" wheels. All wheels were treaded with blue nitrile. Center direct drive shaft was supported with a bearing in the outer plate. Two other axles were dead shafts with bearings in the wheel.

The high load situation I believe created the problem was encountered when the driver returned the control stick to a neutral position with the robot at a high speed. The auto shifting code would have immediately tried to shift the robot to low gear with all three cim motors braking.

I've spent a fair amount of time "behind the glass" as it were. I'd challenge you to find a driver who pushed their robot harder and drove more aggressively.

I truly believe that we saw this failure because we pushed the design to its performance limit and shaft deflection leading to angular gear misalignment and ultimately gear tooth failure was the manifestion of that failure. If it had been on only one drive train side or it only happened one time I would write it off as bad luck, but that was not the case.
__________________
2006-2008 FIRST Team 1741 Red Alert-Founding Student
2008-2011 FIRST Team 1747 Harrison Boiler Robotics-College Mentor
2012 FIRST Team 4272 Maverick Boiler Robotics-Founding College Mentor
2013-Present FIRST Team 1747 Harrison Boiler Robotics-Engineering Mentor
2015-Present Ri3D Team Indiana - Mechanical and Fabrication
 


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 14:59.

The Chief Delphi Forums are sponsored by Innovation First International, Inc.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright © Chief Delphi