|
|
|
![]() |
|
|||||||
|
||||||||
![]() |
| Thread Tools | Rate Thread | Display Modes |
|
#1
|
||||
|
||||
|
G43 loophole
G43 seems to have a loophole.
If you are in contact with a defense, but your bumpers are not breaking the plane of the outer works (for instance, you have grabbed the top of the drawbridge and are pulling it down by backing away from the outer works), are you still protected? The way the rules are now written I don't think so. That means that once a robot begins opening the category C defenses, as soon as its bumper clears the plane of the outer works, you can ram them away from the defense. I expect that to be rectified in a team update. |
|
#2
|
|||
|
|||
|
Re: G43 loophole
G43: ROBOTS on the same half of the FIELD as their ALLIANCE TOWER may not interfere with opponent ROBOTS attempting to traverse OUTER WORKS (regardless of direction). A ROBOT is considered traversing the opponent’s OUTER WORKS if any part of its BUMPERS are within the opponent’s OUTER WORKS.
So by this, we know that "A ROBOT is considered traversing the opponent’s OUTER WORKS if any part of its BUMPERS are within the opponent’s OUTER WORKS." But the rule, however, also states that "You may not interfere with opponent ROBOTS attempting to traverse. It doesn't say they have to be traversing. If they're in contact with a defense, I think it will be obvious that they're "attempting to traverse" the outer-works. Hope maybe that this clarifies the issues with how the rule is worded? |
|
#3
|
||||
|
||||
|
Re: G43 loophole
I understand the wording, including the "attempting to traverse". Also, I believe the intent of the rule is to not allow such defense. However, the way "traversing" is defined is very specific.:
Quote:
|
|
#4
|
||||
|
||||
|
Re: G43 loophole
True, but as AndyBare said, the robot does not have to be traversing the defense, only attempting to traverse.
|
|
#5
|
|||
|
|||
|
Re: G43 loophole
Wow this is Intresting
|
|
#6
|
||||
|
||||
|
Re: G43 loophole
Please read the definition of traversing (highlighted in red above)
|
|
#7
|
|||
|
|||
|
Re: G43 loophole
But all you need to do is attempt to traverse. He understands that.
|
|
#8
|
||||
|
||||
|
Re: G43 loophole
How you define "attempting" could be very different than he does though. Does the lead up to a traverse fall under "attempting"? What about when you fail a traverse? When does the "attempt" end?
|
|
#9
|
||||
|
||||
|
Re: G43 loophole
Quote:
"A DEFENSE is CROSSED by a ROBOT when that ROBOT ■ starts free of contact with the DEFENSE and completely in the NEUTRAL ZONE" So the robot is also in the process of crossing if it is not "free of contact with the DEFENSE" so the robot is then protected. |
|
#10
|
|||
|
|||
|
Re: G43 loophole
Note: If you have an extension that is holding the door open, and that extension is in the Outerworks, then the robot is in the outerworks.
Note2: The door does extend into the neutral zone, so there could be a time when the robot is full outside of Outerworks, yet still in contact with the defense. Maybe a Q&A requesting a clarification that robot is "in the outerworks" or "in contact with the defense". |
|
#11
|
||||
|
||||
|
Re: G43 loophole
Quote:
A ROBOT is considered traversing the opponent’s OUTER WORKS if any part of its BUMPERS are within the opponent’s OUTER WORKS. If you backup to pull down the bridge you are no longer breaking the plane of the outer works |
|
#12
|
|||
|
|||
|
Re: G43 loophole
Quote:
|
|
#13
|
||||
|
||||
|
Re: G43 loophole
No. They defined traversing and contact is not listed anywhere
|
|
#14
|
||||
|
||||
|
Re: G43 loophole
Since there is no definition in the rules for "attempting to traverse", then "attempting" has no meaning withing the rules.
So, how does a ref decide if a robot is "attempting"? Is moving towards the defense attempting? It could be, because The robot is attempting to get to the outer works. There is no way the GDC will allow such an ambiguous definition to stand. Expect a team update where they include "contacting any part of the defense" to the definition of "traversing". Last edited by martin417 : 01-10-2016 at 05:22 PM. |
|
#15
|
|||
|
|||
|
Re: G43 loophole
Bingo
|
![]() |
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|