|
|
|
![]() |
|
|||||||
|
||||||||
![]() |
| Thread Tools | Rate Thread | Display Modes |
|
#16
|
|||
|
|||
|
Re: Co processor Question
You might also look at this board:DE0-NANO-SOC.
CPU is a dual core A9 @ 925 MHz, 1 GB DDR3 (32-bit wide) plus FPGA. DISCLAIMER: I work for Intel (Altera). |
|
#17
|
|||
|
|||
|
Re: Co processor Question
Just learned about the Kangaroo. Since it is a Windows desktop, it can be treated much like a DB computer, so RoboRealm, LV examples, and much other SW will run on it and be easily debugged for it.
Greg McKaskle |
|
#18
|
||||
|
||||
|
Re: Co processor Question
Quote:
|
|
#19
|
|||
|
|||
|
Re: Co processor Question
Quote:
However, I've also been told on numerous occasions that our SoC product line (e.g. the Cyclone V SoC on the DE0 Nano SoC board) will have a long life and will have new, ARM-based variants. Anyhow, I do like this board. I sit beside the marketing guy who oversaw development and was happy to provide him suggestions during that time frame so that it would be useful to robotic applications. This includes the Arduino style headers. There are some things I'd fix on it, but overall, it is a very powerful little guy. |
|
#20
|
||||
|
||||
|
Re: Co processor Question
Quote:
Quote:
Last edited by techhelpbb : 21-01-2016 at 12:45. |
|
#21
|
|||
|
|||
|
Re: Co processor Question
I'll measure that tonight. The wall wart that comes in the kit is 2A @ 5V.
Scott |
|
#22
|
|||
|
|||
|
Re: Co processor Question
Anybody using the RPi 2? We were planning on using it this year, but not entirely sure it will be powerful enough.
|
|
#23
|
||||
|
||||
|
Re: Co processor Question
Quote:
Once we get into the $300 range you start getting into the laptop range. Starts not to make sense anymore. Just buy the laptop. Last edited by techhelpbb : 21-01-2016 at 16:33. |
|
#24
|
|||
|
|||
|
Re: Co processor Question
Size/Weight says keep the micro...hmm..... I need to look more into this kangaroo.
|
|
#25
|
|||
|
|||
|
Re: Co processor Question
Ok, so rookie team, with a question: I thought everything had to be powered off the robot battery, so how can we use the Kangaroo with the integrated?
|
|
#26
|
||||
|
||||
|
Re: Co processor Question
Quote:
Since none of these devices are allowed to instruct the robot to move directly the risk to leaving it on is somewhat mitigated. A few years ago we put a netbook with an SSD minus the screen and keyboard on the robot and it was often left on then charged in the pits. Of course if your device does not have a battery and you run an operating system that doesn't like being abruptly shut down, then you need to start a shutdown rapidly before you turn off the robot master breaker. The ODroid XU4 I mentioned above can boot in 20 seconds and shutdown faster than that. It also has a button one can use to start the shutdown without resorting to hooking up a mouse/keyboard/monitor. That button does require some software tweaking to work like that, normally it simply brings up the shutdown screen in Mate. |
|
#27
|
|||
|
|||
|
Re: Co processor Question
Under the custom circuitry rule, you can use a power supply to convert the battery voltage to a regulated voltage suitable for the end device provided doing so does not violate any other rules (e.g. R41, 24V limit)
The Kangaroo requires a 12V 3A input. I do not recommend a direct battery connection as the battery voltage can fluctuate wildly during a match. What you can do is acquire a 6-18V to 12V voltage regulator and use that for powering the Kangaroo. On a related note, I have seen people add laptops to the robot powered by their internal battery under rule R31). |
|
#28
|
||||
|
||||
|
Re: Co processor Question
Quote:
This is the real weight and size value to it versus say the ODroid XU4. With the ODroid there's no COTS battery. So it must have power from the robot. It is very likely I can place in the footprint of the face of the Kangaroo the ODroid XU4 and the support power system but it will be heavier and thicker by some amount. On the other hand the USB to Ethernet dongle will make the face of the Kangaroo a little larger. Price wise the Kangaroo plus the USB to Ethernet dongle are in line with the price of the ODroid XU4, the case for it, and the old D-Link DC/DC converter. If one adds a boost converter to the Odroid XU4 system then the ODroid XU4 is slightly more expensive to use for this. Ubuntu on the ODroid is 32bit and Windows on the Kangaroo is 64bit. Not that I think the word width is the big issue here. The National Instrument software may work with the Kangaroo but with the ODroid XU4 you'll probably use OpenCV. I am not sure how long the boot and shutdown on the Kangaroo are. If it is left on between matches it might not matter. Last edited by techhelpbb : 22-01-2016 at 09:35. |
|
#29
|
|||
|
|||
|
Re: Co processor Question
Woops, I missed that it had an internal battery.
If anyone has some vision benchmarks between ODroid, Kangaroo, and Tegra TK1, I'd be interested. As an aside, it is legal to use a 2nd RIO as a coprocessor (albeit expensively, R11) |
|
#30
|
||||
|
||||
|
Re: Co processor Question
Quote:
There are multiple ODroid boards so which ones interest you? Which vision system on the Kangaroo? |
![]() |
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|